DTC B2282 Vehicle Speed Signal Malfunction |
DTC B2283 Vehicle Speed Sensor Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B2282 | The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match. |
| Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds. |
| B2283 | Vehicle speed signal malfunction detection : Excessive deceleration is detected (1-trip detection logic*) |
| Drive the vehicle for 30 seconds or more at a vehicle speed of 50 km/h (31 mph) or more. |
| DTC Code | Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
| B2282 |
| - |
| B2283 |
| Steering lock operation is prohibited. |

| DTC | Data List Item | Active Test Item |
| B2282 B2283 | Power Source Control
Combination Meter
| - |
| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Data List.
Check the Data List for proper functioning of the vehicle speed signal.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed Meter | Vehicle speed/Min.: 0, Max.: 255 | Almost same as actual vehicle speed (Speedometer tester) | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER |
Enter the following menus: Body / Power Source Control / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle speed signal | Vehicle being driven or stopped/Stop or Run | Stop: Vehicle stopped Run: Vehicle being driven at 5 km/h (3 mph) or more | - |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Disconnect the G77 connector from the certification ECU (smart key ECU assembly).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G77-2 (+B) - Body ground | Power switch off | 11 to 14 V |
| *a | Rear view of wire harness connector (to Certification ECU (Smart Key ECU Assembly)) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G77-11 (E) - Body ground | Always | Below 1 Ω |
| *a | Rear view of wire harness connector (to Certification ECU (Smart Key ECU Assembly)) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - COMBINATION METER ASSEMBLY) |
Disconnect the G79 connector from the certification ECU (smart key ECU assembly).
Disconnect the G1 connector from the combination meter assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G79-27 (SPD) - G1-39 (+S) | Always | Below 1 Ω |
| G79-27 (SPD) or G1-39 (+S) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Reconnect the G79 certification ECU (smart key ECU assembly) connector.

Reconnect the G1 combination meter assembly connector.
Connect an oscilloscope to terminal G79-27 (SPD) and G77-11 (E).
Turn the power switch on (IG).
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
| Tester Connection | G79-27 (SPD) - G77-11 (E) |
| Tool setting | 5 V/DIV., 100 ms./DIV. |
| Vehicle condition | Power switch on (READY), vehicle being driven at approx. 5 km/h (3 mph) |
| *a | Component with harness connected Certification ECU (Smart Key ECU Assembly) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR) |
Disconnect the 3B junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G1-39 (+S) - 3B-15 | Always | Below 1 Ω |
| G1-39 (+S) or 3B-15 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G79-27 (SPD) - 3A-37 | Always | Below 1 Ω |
| G79-27 (SPD) or 3A-37 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||