Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P3107-215    Lost Communication with Airbag System Control Module

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P3107-213 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3107
215
Abnormal communication signal
  1. Wire harness or connector
  2. Airbag sensor assembly
  3. Power management control ECU

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 .
Refer to the wiring diagram for DTC P3107-213 .

INSPECTION PROCEDURE

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 15 seconds or more.

1.CHECK DTC OUTPUT (SRS AIRBAG)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Body / SRS Airbag / DTC.

  1. Check if DTCs are output.

Result:
Result
Proceed to
Airbag system DTCs are not output.
A
Airbag system DTCs are output.
B

  1. Turn the power switch off.



B
GO TO DTC CHART (AIRBAG SYSTEM) (Click here)
A


2.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


3.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P3107-215 is not output.
    A
    P3107-215 is output again.
    B

  1. Turn the power switch off.



B
Go to step 5
A


4.CHECK FOR INTERMITTENT PROBLEMS
(Click here)


NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

5.CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)
  1. Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.

  1. Turn the power switch on (READY).



    A216762E10
  1. Measure the waveform.
    Item
    Contents
    Terminal
    G18-14 (GSW2) - G18-25 (E1)
    Equipment Setting
    5V/DIV., 500ms/DIV.
    Condition
    Power switch on (READY)

    Result:
    Result
    Proceed to
    The waveform appears as shown in the illustration.
    A
    The waveform differs from the one shown in the illustration.
    B

    Text in Illustration  
    *a
    Component with harness connected
    (Airbag Sensor Assembly)

  1. Turn the power switch off.



B
Go to step 6
A

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

6.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)


    A279820E01
  1. Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (Click here).
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


7.CHECK CONNECTOR CONNECTION CONDITION (AIRBAG SENSOR ASSEMBLY CONNECTOR)


    A216765E06
  1. Check the connector connections and contact pressure of the relevant terminals for the airbag sensor assembly connectors.
    Text in Illustration 
    *a
    Component with harness connected
    (Airbag Sensor Assembly)

    OK:
    The connectors are connected securely and there are no contact pressure problems.



NG
CONNECT SECURELY
OK


8.CHECK HARNESS AND CONNECTOR (+B SHORT)


    A263605E01
  1. Remove the IGCT No. 2 fuse and AM2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    AM2 Fuse
    *3
    IGCT No. 2 Fuse



    A216763E18
  1. Disconnect connector G18 from the airbag sensor assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Airbag Sensor Assembly)



    A243895E21
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - A38-2 (+B2)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-1 (IG2)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-2 (IG2D)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-5 (+B1)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-6 (MREL)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-1 (AM22)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-14 (SPDI)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-1 (ACCD)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-2 (IG1D)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-7 (AM21)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

  1. Connect the airbag sensor assembly connector.

  1. Install the IGCT No. 2 fuse and AM2 fuse.



NG
Go to step 10
OK


9.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)
  1. Disconnect connector G57 from the power management control ECU.

  1. Disconnect connector G18 from the airbag sensor assembly.



    A216764E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - G18-14 (GSW2)
    Power switch off
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) or G18-14 (GSW2) - Body ground and other terminals
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)
    *b
    Rear view of wire harness connector
    (to Airbag Sensor Assembly)

    HINT:
    As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.

  1. Connect the airbag sensor assembly connector.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)  

10.CHECK HARNESS AND CONNECTOR (SHORT TO POWER SUPPLY WIRES)


    A263605E01
  1. Remove the IGCT No. 2 fuse and AM2 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.
    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    AM2 Fuse
    *3
    IGCT No. 2 Fuse



    A216763E18
  1. Disconnect connector G18 from the airbag sensor assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Airbag Sensor Assembly)

  1. Disconnect all the connectors from the power management control ECU.



    A238662E51
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-29 (ABFS) - A38-2 (+B2)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-1 (IG2)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-2 (IG2D)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-5 (+B1)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - A39-6 (MREL)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-1 (AM22)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G57-14 (SPDI)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-1 (ACCD)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-2 (IG1D)
    Power switch off
    10 kΩ or higher
    G57-29 (ABFS) - G58-7 (AM21)
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

  1. Connect the airbag sensor assembly connector.

  1. Connect the power management control ECU connectors.

  1. Install the IGCT No. 2 fuse and AM2 fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)