SMART ENTRY AND START SYSTEM (for Start Function) > TERMINALS OF ECU |
| CHECK POWER MANAGEMENT CONTROL ECU |

Disconnect the A39, G57 and G58 connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
| A39-2 (IG2D) - Body ground | Output | P - Body ground | IG2 signal | 20°C (68°F) | Approximately 302.97 Ω | IG2 Relay Monitor(Outside) |
| A39-23 (STP) - Body ground | Input | L - Body ground | Stop light switch signal | Brake pedal released → Brake pedal depressed | 9 V or higher → 1 V or less | Stop Light Switch1 |
| G57-1 (AM22) - Body ground | Input | B - Body ground | Power source | Power switch off | 11 to 14 V | - |
| G58-7 (AM21) - Body ground | Input | B - Body ground | Power source | Power switch off | 11 to 14 V | - |
| G58-16 (SLP) - Body ground | Input | P - Body ground | Steering lock position signal | Always | 10 kΩ or higher | Steering Unlock Switch |
| G57-5 (E01) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| G58-5 (E02) - Body ground | - | W-B - Body ground | Ground | Always | Below 1 Ω | - |
| G57-6 (E1) - Body ground | - | BR - Body ground | Ground | Always | Below 1 Ω | - |
| G58-17 (SSW2) - Body ground | Input | SB - Body ground | SSW2 contact signal
| Power switch pushed → Power switch not pushed | Below 1 Ω → 10 kΩ or higher | Start Switch2 |
| G57-7 (SSW1) - Body ground | Input | V - Body ground | SSW1 contact signal | Power switch pushed → Power switch not pushed | Below 1 Ω → 10 kΩ or higher | Start Switch1 |
| G58-2 (IG1D) - Body ground | Output | SB - Body ground | IG1 signal | 20°C (68°F) | 40.74 to 59.49 Ω | IG1 Relay Monitor(Outside) |
| G58-1 (ACCD) - Body ground | Output | L - Body ground | ACC signal | 20°C (68°F) | 81.49 to 118.98 Ω | ACC Relay Monitor |
| G57-14 (SPDI) - G57-6 (E1) | Input | SB - BR | Vehicle speed signal | Always | 30 kΩ or higher | Vehicle Speed Signal |
| G57-15 (P2) - G57-6 (E1) | Input | G - BR | P position signal | Always | 40 kΩ or higher → 200 Ω or less | Shift P Signal |
Reconnect the A39, G57 and G58 connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
| A39-2 (IG2D) - G57-6 (E1) | Output | P - BR | IG2 signal | Power switch on (ACC) → Power switch on (IG) | 1 V or less → 9 V or higher | IG2 Relay Monitor(Outside) |
| G58-16 (SLP) - G57-6 (E1) | Input | P - BR | Steering lock position signal | Steering wheel locked → Steering wheel unlocked*1 | 11 to 14 V → 1.2 V or less | Steering Unlock Switch |
| G58-6 (SLR+) - G57-6 (E1) | Output | L - BR | Steering lock motor operation command signal (Steering lock motor operation permission signal sent from the power management control ECU) | Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped*2 | Pulse generation (See waveform 1) | - |
| G58-17 (SSW2) - G57-6 (E1) | Input | SB - BR | SSW2 contact signal
| Power switch not pushed → Power switch pushed | 9 V or higher → 1 V or less | Start Switch2 |
| G57-7 (SSW1) - G57-6 (E1) | Input | V - BR | SSW1 contact signal | Power switch not pushed → Power switch pushed | 9 V or higher → 1 V or less | Start Switch1 |
| G58-1 (ACCD) - G57-6 (E1) | Output | L - BR | ACC signal | Power switch off → Power switch on (ACC) | 1 V or less → 8.5 V or higher | ACC Relay Monitor |
| G58-2 (IG1D) - G57-6 (E1) | Output | SB - BR | IG1 signal | Power switch on (ACC) → Power switch on (IG) | 1 V or less → 9 V or higher | IG1 Relay Monitor(Outside) |
| G57-14 (SPDI) - G57-6 (E1) | Input | SB - BR | Vehicle speed signal | Vehicle being driven at approx. 5 km/h (3 mph) | Pulse generation (See waveform 2) | Vehicle Speed Signal |
| G57-15 (P2) - G57-6 (E1) | Input | G - BR | P position signal | Shift lever in P → Shift lever not in P | Pulse generation (See waveform 3) | Shift P Signal |
| G58-20 (IMO) - G57-6 (E1) | Output | BE - BR | ID code box communication output (Signal output from power management control ECU to ID code box) | Power switch off | 11 to 14 V | - |
| Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected | Pulse generation (See waveform 4) | |||||
| G58-21 (IMI) - G57-6 (E1) | Input | LG - BR | ID code box communication input (Signal input from ID code box to power management control ECU) | Power switch off | 11 to 14 V | |
| Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected | Pulse generation (See waveform 5) |
Using an oscilloscope, check the waveform of the ECU.
![]() |
Waveform 1
| Item | Content |
| Tester Connection | G58-6 (SLR+) - G57-6 (E1) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped |
| *a | Steering lock motor not operating |
| *b | Steering lock motor operating |
![]() |
Waveform 2
| Item | Content |
| Tester Connection | G57-14 (SPDI) - G57-6 (E1) |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle Condition | Power switch on (IG), vehicle being driven at approx. 5 km/h (3 mph) |
![]() |
Waveform 3
| Item | Content |
| Tester Connection | G57-15 (P2) - G57-6 (E1) |
| Tool Setting | 2 V/DIV., 50 ms./DIV. |
| Vehicle Condition | Shift lever in P → Shift lever not in P |
| *a | Shift lever in P |
| *b | Shift lever not in P |
Waveform 4

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | G58-20 (IMO) - G57-6 (E1) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Vehicle Condition | Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected |
Waveform 5

| *a | Approximately 160 ms | *b | Approximately 270 ms |
| Item | Content |
| Tester Connection | G58-21 (IMI) - G57-6 (E1) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Vehicle Condition | Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected |