Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

SMART ENTRY AND START SYSTEM (for Start Function) > TERMINALS OF ECU

for Preparation Click here



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E90

  1. Disconnect the G77 and G79 connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    G77-2 (+B) - Body ground
    Input
    B - Body ground
    Power source
    Power switch off
    11 to 14 V
    -
    G77-9 (IG2D) - Body ground
    Output
    P - Body ground
    IG2 signal
    20°C (68°F)
    Approximately 302.97 Ω
    IG2 Relay Monitor(Outside)
    G77-11 (E) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    G77-18 (STP1) - Body ground
    Input
    G - Body ground
    Stop light switch signal
    Brake pedal released → Brake pedal depressed
    1 V or less → 9 V or higher
    Stop Light Switch1
    G79-4 (ACCD) - Body ground
    Output
    L - Body ground
    ACC signal
    20°C (68°F)
    81.49 to 118.98 Ω
    ACC Relay Monitor
    G79-6 (IG1D) - Body ground
    Output
    SB - Body ground
    IG1 signal
    20°C (68°F)
    40.74 to 59.49 Ω
    IG1 Relay Monitor(Outside)
    G79-25 (P) - G77-11 (E)
    Input
    G - W-B
    P position signal
    Shift lever in P → Shift lever not in P
    40 kΩ or higher → 200 Ω or less
    Shift P Signal
    G79-26 (SLP) - Body ground
    Input
    P - Body ground
    Steering lock position signal
    Steering wheel locked
    10 kΩ or higher
    Steering Unlock Switch
    G79-27 (SPD) - G77-11 (E)
    Input
    SB - W-B
    Vehicle speed signal
    Always
    30 kΩ or higher
    Vehicle Speed Signal
    G79-28 (SSW1) - Body ground
    Input
    V - Body ground
    SSW1 contact signal
    Power switch pushed → Power switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch1
    G79-30 (SSW2) - Body ground
    Input
    SB - Body ground
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Power switch pushed → Power switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch2

  3. Reconnect the G77 and G79 connectors.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    G77-9 (IG2D) - G77-11 (E)
    Output
    P - W-B
    IG2 signal
    Power switch on (ACC) → Power switch on (IG)
    1 V or less → 9 V or higher
    IG2 Relay Monitor(Outside)
    G79-4 (ACCD) - G77-11 (E)
    Output
    L - W-B
    ACC signal
    Power switch off → Power switch on (ACC)
    1 V or less → 8.5 V or higher
    ACC Relay Monitor
    G79-6 (IG1D) - G77-11 (E)
    Output
    SB - W-B
    IG1 signal
    Power switch on (ACC) → Power switch on (IG)
    1 V or less → 9 V or higher
    IG1 Relay Monitor(Outside)
    G79-25 (P) - G77-11 (E)
    Input
    G - W-B
    P position signal
    Shift lever in P → Shift lever not in P
    9 V or higher → 1.5 V or less
    Shift P Signal
    G79-26 (SLP) - G77-11 (E)
    Input
    P - W-B
    Steering lock position signal
    Steering wheel locked → Steering wheel unlocked*1
    11 to 14 V → 1.2 V or less
    Steering Unlock Switch
    G79-27 (SPD) - G77-11 (E)
    Input
    SB - W-B
    Vehicle speed signal
    Vehicle being driven at approx. 5 km/h (3 mph)
    Pulse generation
    (See waveform 2)
    Vehicle Speed Signal
    G79-28 (SSW1) - G77-11 (E)
    Input
    V - W-B
    SSW1 contact signal
    Power switch not pushed → Power switch pushed
    9 V or higher → 1 V or less
    Start Switch1
    G79-29 (SLR+) - G77-11 (E)
    Output
    L - W-B
    Steering lock motor operation command signal (Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))
    Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped*2
    Pulse generation (See waveform 1)
    -
    G79-30 (SSW2) - G77-11 (E)
    Input
    SB - W-B
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Power switch not pushed → Power switch pushed
    9 V or higher → 1 V or less
    Start Switch2

    HINT:
    1. *1: When the power switch is turned off with the shift lever in P and any of the doors are opened or closed, the steering wheel will be locked. When the power switch is turned on (ACC) or on (IG), the steering wheel will be unlocked.
    2. *2: Perform the following procedure to operate the steering lock motor.
      1. The shift lever is in P.
      2. The power switch is off.
      3. While carrying the electrical key transmitter sub-assembly, the power switch is turned on (IG) and the steering is unlocked.



  5. Using an oscilloscope, check the waveform of the ECU.



      C221561E01
    1. Waveform 1
      Item
      Content
      Tester Connection
      G79-29 (SLR+) - G77-11 (E)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Vehicle Condition
      Steering lock motor stopped →
      Steering lock motor operating →
      Steering lock motor stopped
      Text in Illustration 
      *a
      Steering lock motor not operating
      *b
      Steering lock motor operating

      HINT:
      When all of the following conditions are met, open any of the doors to operate the steering lock motor.
      1. The shift lever is in P.
      2. While carrying the electrical key transmitter sub-assembly, the power switch is turned on (IG) and the steering is unlocked.
      3. The power switch is off.



    2. B220145E01
    3. Waveform 2
      Item
      Content
      Tester Connection
      G79-27 (SPD) - G77-11 (E)
      Tool Setting
      5 V/DIV., 20 ms./DIV.
      Vehicle Condition
      Power switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

      HINT:
      The wavelength becomes shorter as the vehicle speed increases.


HYBRID VEHICLE CONTROL ECU

B363792E02



  1. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    G81-23 (IMO) - G80-6 (E1)
    Output
    BE - BR
    ID code box communication output
    (Signal output from hybrid vehicle control ECU to ID code box)
    Power switch off
    11 to 14 V
    -
    Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
    Pulse generation
    (See waveform 1)
    G81-22 (IMI) - G80-6 (E1)
    Input
    LG - BR
    ID code box communication input
    (Signal input from ID code box to hybrid vehicle control ECU)
    Power switch off
    11 to 14 V
    Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected
    Pulse generation
    (See waveform 2)



    1. Waveform 1


      B278942E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      G81-23 (IMO) - G80-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Vehicle Condition
      Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected



    2. Waveform 2


      B278943E01


      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Measurement Condition 
      Item
      Content
      Tester Connection
      G81-22 (IMI) - G80-6 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Vehicle Condition
      Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected