Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

SMART ENTRY AND START SYSTEM (for Start Function) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Data List.



  5. According to the display on the intelligent tester, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift P Signal
    Shift position P/ON or OFF
    ON: Shift lever in P
    OFF: Shift lever not in P
    1. Use this item to determine if the shift position switch is malfunctioning.
    2. The hybrid control system cannot be started when this item is OFF.
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF
    ON: Steering unlocked
    OFF: Steering locked
    1. When the shift lever is in P and the power switch is off, if any door is opened then closed, the steering is locked.
    2. When the electrical key transmitter sub-assembly is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The hybrid control system cannot be started when the steering unlock signal is off.
    Stop Light Switch1
    State of brake pedal/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The hybrid control system cannot be started when this item is OFF.
    3. When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.
    Start Switch1
    Power switch 1 status/ON or OFF
    ON: Power switch pressed
    OFF: Power switch not pressed
    1. If the power switch is pressed for a short time, the display may not change.
    2. Use this item to determine whether the power switch input signal is malfunctioning.
    Start Switch2
    Power switch 2 status/ON or OFF
    ON: Power switch pressed
    OFF: Power switch not pressed
    1. Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.
    2. Behaves the same way as power switch 1.
    Latch Circuit
    Status of IG related backup circuits/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    1. Displays in almost the same manner as the IG1 and IG2 relays.
    2. When the power switch is on (ACC), OFF is displayed.
    IG1 Relay Monitor(Outside)
    IG1 relay coil voltage monitor status/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    1. Use this item to determine whether the IG1 relay is malfunctioning.
    2. When the power switch is on (ACC), OFF is displayed.
    IG1 Relay Monitor(Inside)
    IG1 relay activation/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    1. Use this item to determine whether the IG1 relay is malfunctioning.
    2. When the power switch is on (ACC), OFF is displayed.
    IG2 Relay Monitor(Outside)
    IG2 relay coil voltage monitor status/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    1. Use this item to determine whether the IG2 relay is malfunctioning.
    2. When the power switch is on (ACC), OFF is displayed.
    IG2 Relay Monitor(Inside)
    IG2 relay activation/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    1. Use this item to determine whether the IG2 relay is malfunctioning.
    2. When the power switch is on (ACC), OFF is displayed.
    Starter Request Signal
    hybrid control system start request signal status/ON or OFF
    ON: With the shift lever in P and brake pedal depressed, the power switch is pressed and held
    OFF: After approx. 1 sec. has elapsed, the power switch is released
    1. When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.
    2. When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain amount of time.
    ACC Relay Monitor
    ACC relay activation/ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    1. When the power switch is on (IG), ON is displayed.
    Ready Signal
    Ready signal/ON or OFF
    ON: Hybrid control system on (on (READY))
    OFF: Hybrid control system off
    -
    Vehicle Speed Signal
    Vehicle being driven or stopped/Stop or Run
    Stop: Vehicle stopped
    Run: Vehicle being driven at 5 km/h (3 mph) or more
    -
    Power Supply Condition
    Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    All OFF: Power switch off
    ACC ON: Power switch on (ACC)
    IG1 ON: Power switch on (IG) (IG1 relay on)
    IG2 ON: Power switch on (IG) (IG2 relay on)
    ST ON: Sending hybrid control system start request signal
    Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
    Powertrain Type
    Vehicle identification/HV-AT, Cnv-MT, Cnv-AT, Cnv-MMT, S&S-MT, S&S-AT or S&S-MMT
    HV-AT
    -
    IG1 Circuit
    IG1 relay coil circuit malfunction/OK or NG
    OK: Circuit normal
    NG: Circuit malfunctioning
    1. Use this item to determine whether the IG1 relay is malfunctioning.
    2. When the hybrid control system cannot be started due to an IG1 relay malfunction, NG is displayed.
    IG2 Circuit
    IG2 relay coil circuit malfunction/OK or NG
    OK: Circuit normal
    NG: Circuit malfunctioning
    1. Use this item to determine whether the IG2 relay is malfunctioning.
    2. When the hybrid control system cannot be started due to an IG2 relay malfunction, NG is displayed.
    Starter SW Sig Mismatch
    Power switch signal 1 and 2 do not match/Yes or No
    Yes: Switch malfunctioning (power switch signal 1 and 2 do not match)
    No: Switch normal
    The hybrid control system can be started even if the result is Yes. However, emergency hybrid control system off while driving by pressing and holding the power switch and, when the brakes are malfunctioning, emergency hybrid control system by pressing and holding the power switch cannot be performed.
    Park Signal Mismatch
    P position signal malfunction/Yes or No
    Yes: Signal malfunction (CAN communication and direct line signal do not match)
    No: Signal normal
    Even when Yes is displayed, it is still possible to turn the power switch off (the power source mode will not be stuck in on (ACC) or on (IG)).
    Str Lock/Unlock Wait T-Out
    Steering lock or unlock malfunction/Yes or No
    Yes: Lock or unlock malfunction (e.g. steering lock is stuck etc.)
    No: Lock and unlock normal
    When the hybrid control system cannot be started due to a steering lock or unlock malfunction, Yes is displayed.
    Key Certif Wait T-Out
    Key verification malfunction/Yes or No
    Yes: Verification error (detected due to the electrical key transmitter sub-assembly ID code and the ID code stored in the certification ECU (smart key ECU assembly) not matching)
    No: Verification normal
    When the hybrid control system cannot be started due to a key verification error, Yes is displayed.
    Number of Diagnosis Code
    Number of DTCs/0 to 255
    -
    -


    B288114E01

    HINT:
    To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the power switch off and the shift lever in P.
    *1: Press the power switch with the brake pedal released and check that the power switch is turned on (ACC).
    *2: Press the power switch with the brake pedal released and check that the power switch is turned on (IG).
    *3: Depress the brake pedal (stop light switch is on).
    *4: Press the power switch with the brake pedal depressed and check that the hybrid control system starts.
    *5: Press the power switch with the brake pedal depressed and check that the power switch is turned off.
    *6: Release the brake pedal.
    *7: Open a door.


    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ignition Switch
    Certification ECU (smart key ECU assembly) IG power supply input status/ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    When the power switch is on (ACC), OFF is displayed.
    #Codes
    Number of DTCs/0 to 255
    -
    -
    Immobiliser
    Engine immobiliser system status determined by certification ECU (smart key ECU assembly) / Set or Unset
    Set: Engine immobiliser system set (hybrid control system start prohibited) (power switch off)
    Unset: Engine immobiliser system unset (hybrid control system start permitted) (power switch on (ACC) or on (IG))
    The hybrid control system cannot be started when Set is displayed.

    HINT:
    1. The security indicator light blinks when Set is displayed.
    2. The security indicator light is linked with set/unset of the immobiliser and not linked with steering lock/unlock.

    Steering Lock Sleep Cond
    Steering lock ECU (steering lock actuator assembly) sleep availability/Yes or No
    Yes: Sleep available
    No: Sleep not available
    -
    Steering Lock Start Cond
    Steering lock ECU (steering lock actuator assembly) wake up signal status/Yes or No
    Yes: Wake up signal sent
    No: Wake up signal not sent
    -
    Engine Start Condition
    Status of hybrid control system start permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/OK or NG
    OK: hybrid control system start permitted
    NG: hybrid control system start prohibited
    1. When Permitted is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly) and starting of the hybrid control system possible.
    2. The hybrid control system cannot be started when Prohibited is displayed.
    Sensor Value
    History of malfunction of position sensor in steering lock ECU (steering lock actuator assembly)/OK or NG(Past)
    OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator assembly) does not exist.
    NG(Past): History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator assembly) being on exists (Under normal operation, neither sensor is on).
    When NG (Past) is displayed, either the position sensor in the steering lock ECU (steering lock actuator assembly) or the assembly itself may be malfunctioning.
    Power Supply Short
    History of signal error (short) sent from certification ECU (smart key ECU assembly) to steering lock ECU (steering lock actuator assembly)/OK or NG(Past)
    OK: History of motor power source short does not exist
    NG(Past): History of motor power source short exists
    This item displays history when a malfunction exists in the circuit between the certification ECU (smart key ECU assembly) and the steering lock ECU (steering lock actuator assembly).
    Motor Driver Short
    History of malfunction (short) in the steering lock ECU (steering lock actuator assembly) motor circuit (DTC B2781 is stored)./OK or NG(Past)
    OK: History of short in the motor circuit does not exist
    NG(Past): History of short in the motor circuit exists
    History of a malfunction in the steering lock motor circuit in the steering lock ECU (steering lock actuator assembly).
    Lock/Unlock Receive
    History of receiving an unlock request signal/Yes or No
    Yes: History of receiving an unlock request signal exists
    No: History of receiving an unlock request signal does not exist
    -
    Lock Bar Stuck Error
    History of the steering wheel not being able to unlock properly when the steering lock operates for a certain amount of time/OK or NG(Past)
    OK: History of steering lock being stuck does not exist
    NG(Past): History of steering lock being stuck exists
    -
    Push Start Error
    History of push start malfunction due to steering lock ECU (steering lock actuator assembly)/OK or NG(Past)
    OK: History of push start malfunction does not exist
    NG(Past): History of push start malfunction exists
    -
    Engine Start Request
    Status of hybrid control system start permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly)/OK or NG
    OK: Signal received
    NG: Signal not received
    1. When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly) and hybrid control system start possible.
    2. The hybrid control system cannot be started when NG is displayed.
    S Code Check
    Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU)/OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When NG is displayed:
    1. S code has not been registered for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).
    2. Steering cannot be locked.
    3. Steering cannot be unlocked (the hybrid system cannot be started).
    L Code Check
    Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)/OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When NG is displayed:
    1. L code has not been registered for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).
    2. Steering cannot be locked.
    3. Steering cannot be unlocked (the hybrid system cannot be started).
    Unlock Request Receive
    Unlock request signal received state/OK or NG
    OK: Within 10 sec. of turning the power switch on (IG) or on (ACC), or of an hybrid control system start operation being performed
    NG: Power switch on (IG) or on (ACC), or hybrid control system start operation not performed
    1. The hybrid control system cannot be started when an unlock request signal cannot be received.
    2. If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    Lock Request Receive
    Lock request signal received state/OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG".

    OK: Lock request signal received for 10 sec. of any of the doors being opened with shift lever in P and power switch off.
    NG: Except above
    If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    S Code Check(Past)
    Verification result history between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU)/OK or NG(Past)
    OK: History of abnormal verification result does not exist
    NG(Past): History of abnormal verification result exists
    -
    L Code Check(Past)
    Verification result history between the ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly)/OK or NG(Past)
    OK: History of abnormal verification result does not exist
    NG(Past): History of abnormal verification result exists
    -
    Steering Lock
    Steering lock ECU (steering lock actuator assembly) lock confirmation status/Set or Unset
    Set: Lock confirmed
    Unset: Lock not confirmed
    When Unset is displayed, the steering wheel is not locked.
    Steering Unlock
    Steering lock ECU (steering lock actuator assembly) unlock confirmation status/Set or Unset
    Set: Unlock confirmed
    Unset: Unlock not confirmed
    When Unset is displayed, the steering wheel is not locked (the hybrid control system cannot be started).
    Engine Start Indicator
    Smart warning light / ON or OFF
    Customization status displayed
    -

    B279857E01

    HINT:
    To check if the Data List display changes, get into the vehicle while carrying an electrical key transmitter sub-assembly and perform the following operations with the power switch off and the shift lever in P.
    *1: Press the power switch with the brake pedal released and check that the power switch is turned on (ACC).
    *2: Press the power switch with the brake pedal released and check that the power switch is turned on (IG).
    *3: Press the power switch and check that the power switch is turned off.
    *4: Open any of the doors (steering locked).


    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0, Max.: 255
    Almost same as actual vehicle speed (Speedometer tester)
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / (desired system) / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.


Power Source Control 
Tester Display
Test Part
Control Range
Diagnostic Note
P Supply for Steering Lock
Smart key ECU assembly
ON/OFF

HINT:
ON: Power is supplied.
OFF: Power is not supplied.

When performing this Active Test, make sure the following condition is met:
The power switch is on (IG).

Entry&Start 
Tester Display
Test Part
Control Range
Diagnostic Note
Power/Engine SW Light
Power switch light
OFF/ON
When performing this Active Test, make sure the following condition is met:
The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running.