SMART ENTRY AND START SYSTEM (for Entry Function) > DATA LIST / ACTIVE TEST |
| DATA LIST |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start, Main Body, Power Source Control or Combination Meter / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D-Door Touch Sensor* | Driver door touch sensor (unlock sensor) / ON or OFF | ON: Driver door touch sensor (unlock sensor) touched OFF: Driver door touch sensor (unlock sensor) not touched |
|
| P-Door Touch Sensor* | Front passenger door touch sensor (unlock sensor) / ON or OFF | ON: Front passenger door touch sensor (unlock sensor) touched OFF: Front passenger door touch sensor (unlock sensor) not touched |
|
| D-Door Trigger Switch* | Driver door touch sensor (lock sensor) / ON or OFF | ON: Driver door touch sensor (lock sensor) touched OFF: Driver door touch sensor (lock sensor) not touched |
|
| P-Door Trigger Switch* | Front passenger door touch sensor (lock sensor) / ON or OFF | ON: Front passenger door touch sensor (lock sensor) touched OFF: Front passenger door touch sensor (lock sensor) not touched |
|
| Tr/B-Door Lock SW | Back door opener switch assembly (lock switch) / ON or OFF | ON: Back door opener switch assembly (lock switch) pushed OFF: Back door opener switch assembly (lock switch) not pushed |
|
| Tr/B-Door Unlock SW | Luggage door opening switch assembly (unlock switch) / ON or OFF | ON: Luggage door opening switch assembly (unlock switch) pushed OFF: Luggage door opening switch assembly (unlock switch) not pushed |
|
| Ignition Switch | Power switch on (IG) / ON or OFF | ON: Power switch on (IG) OFF: Power switch off |
|
| Unmatched Vehicle-ID | Key No. (incorrect or correct) / Yes or No | Yes: Communication malfunction No: Communication normal | The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List). Other potential causes:
|
| No Response | Communication response / Yes or No | Yes: Communication malfunction No: Communication normal | The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the power switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. If there is wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List.) Other potential causes:
|
| Unmatch Code or Form | Code format (incorrect or correct) / Yes or No | Yes: Communication malfunction No: Communication normal | There is an error in the data sent from the electrical key transmitter sub-assembly (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List). Other potential causes:
|
| Key Low Battery | Transmitter battery depleted / Yes or No | Yes: Transmitter battery depleted No: Transmitter battery not depleted | The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
| Power Save Cnt 10 Min | Number of times power saving control is activated due to electrical key transmitter sub-assembly being in detection area for 10 minutes or more / 0 to 255 | Within range of 0 to 255 | If the electrical key transmitter sub-assembly is in a vehicle exterior detection area, communication is frequently performed between the vehicle and electrical key transmitter sub-assembly, resulting in an increase in transmitter battery power consumption. To prevent the transmitter battery from becoming fully depleted, if the electrical key transmitter sub-assembly is left in the detection area for 10 minutes or more, the smart entry and start system automatically deactivates the exterior detection area the electrical key transmitter is in. If the doors are locked/unlocked with a wireless operation or by the mechanical key, the system resumes operation. |
| Power Save Cnt 5 Days | Number of times power saving control 1 (vehicle exterior periodic signal transmission stop) is activated due to hybrid system not being started for 5 days or more / 0 to 255 | Within range of 0 to 255 | - |
| Power Save Cnt 14 Days | Number of times power saving control 2 (lock/unlock sensor of front door outside handle assembly of front passenger door disabled) is activated due to hybrid system not being started for 14 days or more / 0 to 255 | Within range of 0 to 255 | - |
| #Codes | Number of trouble codes / Min: 0, Max: 255 | Number of stored DTCs displayed | - |
| ID Code Difference(Resp) | ID code (incorrect or correct) / Yes or No | Yes: Communication malfunction No: Communication normal | The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List). Other potential causes:
|
| C Code Difference | Challenge code (incorrect or correct) / Yes or No | Yes: Communication malfunction No: Communication normal | The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List). Other potential causes:
|
| ID Code Difference | Wireless ID code (incorrect or correct) / Yes or No | Yes: Communication malfunction No: Communication normal | The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "ID Code Difference(Resp)" in the Data List.) Other potential causes:
|
| Immobiliser | Key response to signal from certification ECU (smart key ECU assembly) / OK or NG | OK: Key responds to signal from certification ECU (smart key ECU assembly) NG: Key does not respond to signal from certification ECU (smart key ECU assembly) | Problems may be caused by the following:
|
| Different Rolling Code | Rolling code (incorrect or correct) / Yes or No | Yes: Communication malfunction No: Communication normal | The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different Other potential causes:
|
| Auto Entry Cancel SW | Entry cancel function setting / OFF or ON | Mode status displayed ON: Smart entry and start system canceled OFF: Smart entry and start system not canceled | The default setting for the entry cancel function is OFF. If the customer requests that the smart entry and start system functions (locking and unlocking the doors while carrying the electrical key transmitter sub-assembly, etc.) be canceled, the setting can be changed through the customize function (Click here). |
| S Code Check | S code verification result / OK or NG | OK: S code verification result normal NG: S code verification result abnormal | Problems may be caused by the following:
|
| L Code Check | L code verification result / OK or NG | OK: L code verification result normal NG: L code verification result abnormal | Problems may be caused by the following:
|
| Unlock Request Receive | Status of steering unlock command from certification ECU (smart key ECU assembly) / OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of power switch turned on (ACC) or on (IG), or of hybrid system start operation performed) NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (power switch not turned on (ACC) or on (IG), and hybrid system start operation not performed) | - |
| Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly) / OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and power switch off) NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and power switch off) | - |
| S Code Check (Past) | S code verification result (past) / OK or NG (Past) | OK: Verification result normal NG (Past): Verification result abnormal (past) | - |
| L Code Check (Past) | L code verification result (past) / OK or NG (Past) | OK: Verification confirmed (past) NG (Past): Verification not confirmed (past) | - |
| Steering Lock | State of whether steering lock ECU (steering lock actuator assembly) has determined steering is locked / Set or Unset | Set: Steering locked Unset: Steering unlocked | - |
| Steering Unlock | State of whether steering lock ECU (steering lock actuator assembly) determined steering is unlocked / Set or Unset | Set: Steering unlocked Unset: Steering locked | - |
| Short in Driver Side Door Oscillators Circuit | Short in driver side door electrical key antenna circuit / OK or NG | OK: Driver side door electrical key antenna circuit is normally NG: Driver side door electrical key antenna circuit is abnormally | - |
| Short in Front P Side Door Oscillators Circuit | Short in front passenger side door electrical key antenna circuit / OK or NG | OK: Front passenger side door electrical key antenna circuit is normally NG: Front passenger side door electrical key antenna circuit is abnormally | - |
| Short in D Side Door Oscillators Circuit (Hist) | Short in driver side door electrical key antenna circuit (history) / OK or NG (Hist) | OK: Driver side door electrical key antenna circuit was normally NG (Hist): Driver side door electrical key antenna circuit was abnormally | - |
| Short in Fr P Side Door Oscillators Circuit (Hist) | Short in front passenger side door electrical key antenna circuit (history) / OK or NG (Hist) | OK: Front passenger side door electrical key antenna circuit was normally NG (Hist): Front passenger side door electrical key antenna circuit was abnormally | - |
| Door Unlock Mode2 | Door Unlock Mode2 / All or Driver | Customization status displayed | - |
| Ignition Available Area | Ignition available area / Front or All | Customization status displayed | - |
| Parking Wait Time | Parking wait time / 0.5s, 1.5s, 2.5s or 5s | Customization status displayed | - |
| B-Dr Opening Operation | Back door opening operation / Long, Twice, OFF | Customization status displayed | - |
| Touch Activation Over Threshold | Consecutive entry lock operation / Active or Not Active | Customization status displayed | - |
| Wireless Signal Encryption Support | Wireless Signal Encryption Support / Yes or No | Customization status displayed | - |
| Key Low Battery Warning | Low transmitter battery warning / ON or OFF | Customization status displayed | - |
| Key Left in Vehicle Buz | Key left in vehicle buzzer sounds / ON or OFF | Customization status displayed | - |
| Engine Start Indicator | Hybrid system start indicator lights / ON or OFF | Customization status displayed | - |

| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ACC SW | Power switch status / ON or OFF | ON: Power switch on (ACC) OFF: Power switch off | - |
| IG SW | Power switch status / ON or OFF | ON: Power switch on (IG) OFF: Power switch off | - |
| RR Door Courtesy | Rear RH door courtesy light switch / OPEN or CLOSE | OPEN: Rear RH door open CLOSE: Rear RH door closed | - |
| RL Door Courtesy | Rear LH door courtesy light switch / OPEN or CLOSE | OPEN: Rear LH door open CLOSE: Rear LH door closed | - |
| Back Door Courtesy SW | Back door courtesy light switch / ON or OFF | ON: Back door open OFF: Back door closed | - |
| FR Door Lock Pos | Front RH door unlock detection switch signal / UNLOCK or LOCK | UNLOCK: Front RH door unlocked LOCK: Front RH door locked | - |
| FR Door Courtesy | Front RH door courtesy light switch signal / OPEN or CLOSE | OPEN: Front RH door open CLOSE: Front RH door closed | - |
| FL Door Lock Pos | Front LH door unlock detection switch signal / UNLOCK or LOCK | UNLOCK: Front LH door unlocked LOCK: Front LH door locked | - |
| FL Door Courtesy | Front LH door courtesy light switch signal / OPEN or CLOSE | OPEN: Front LH door open CLOSE: Front LH door closed | - |
| RR-Door Lock Pos SW | Rear door RH and LH unlock detection switch signal / ON or OFF | ON: Rear door RH or LH unlocked OFF: Rear door RH and LH locked | - |
| RL-Door Lock Pos SW | Rear door RH and LH unlock detection switch signal / ON or OFF | ON: Rear door RH or LH unlocked OFF: Rear door RH and LH locked | - |
| Hazard Answer Back | Hazard answer-back of entry function / ON or OFF | Customization status displayed | - |
| Open Door Warning | Open door warning / ON or OFF | Customization status displayed | - |
| Auto Lock Time | Automatic lock time / 120 s, 60 s or 30 s | Customization status displayed | - |
| Wireless Buzzer Resp | Buzzer answer-back of entry function / ON or OFF | Customization status displayed | - |
| Wireless Buzzer Vol | Entry door lock buzzer volume / Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0 | Customization status displayed | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift P Signal | Shift position P/ON or OFF | ON: Shift lever in P OFF: Shift lever not in P |
|
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF | ON: Steering unlocked OFF: Steering locked |
|
| Stop Light Switch1 | State of brake pedal/ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
|
| Start Switch1 | Power switch 1 status/ON or OFF | ON: Power switch pressed OFF: Power switch not pressed |
|
| Start Switch2 | Power switch 2 status/ON or OFF | ON: Power switch pressed OFF: Power switch not pressed |
|
| Vehicle Speed Signal | Vehicle being driven or stopped/Stop or Run | Stop: Vehicle stopped Run: Vehicle being driven at 5 km/h (3 mph) or more | - |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed Meter | Vehicle speed / Min.: 0, Max.: 255 | Almost the same as actual vehicle speed | - |
| ACTIVE TEST |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry&Start or Main Body / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Overhead Tuner Power Supply ON | Door control receiver | OFF/ON | - |
| Power for P-Seat Sens | Front door outside handle (for front passenger door) | OFF/ON | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Door Lock | Door lock motor | Unlock/Lock | - |
| Trunk and Back-Door Open | Operate back door lock motor | OFF/ON | - |
| Wireless Buzzer | Wireless door lock buzzer | OFF/ON | - |