Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
  1. Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
  2. When using the intelligent tester with the power switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Entry&Start, Main Body, Power Source Control or Combination Meter / Data List.



  5. Read the Data List according to the display on the intelligent tester.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Touch Sensor*
    Driver door touch sensor (unlock sensor) / ON or OFF
    ON: Driver door touch sensor (unlock sensor) touched
    OFF: Driver door touch sensor (unlock sensor) not touched
    1. Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.
    P-Door Touch Sensor*
    Front passenger door touch sensor (unlock sensor) / ON or OFF
    ON: Front passenger door touch sensor (unlock sensor) touched
    OFF: Front passenger door touch sensor (unlock sensor) not touched
    1. Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate.
    D-Door Trigger Switch*
    Driver door touch sensor (lock sensor) / ON or OFF
    ON: Driver door touch sensor (lock sensor) touched
    OFF: Driver door touch sensor (lock sensor) not touched
    1. Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
    P-Door Trigger Switch*
    Front passenger door touch sensor (lock sensor) / ON or OFF
    ON: Front passenger door touch sensor (lock sensor) touched
    OFF: Front passenger door touch sensor (lock sensor) not touched
    1. Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
    2. Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.
    Tr/B-Door Lock SW
    Back door opener switch assembly (lock switch) / ON or OFF
    ON: Back door opener switch assembly (lock switch) pushed
    OFF: Back door opener switch assembly (lock switch) not pushed
    1. Displays whether the back door opener switch assembly (lock switch) is on or off.
    2. Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate.
    Tr/B-Door Unlock SW
    Luggage door opening switch assembly (unlock switch) / ON or OFF
    ON: Luggage door opening switch assembly (unlock switch) pushed
    OFF: Luggage door opening switch assembly (unlock switch) not pushed
    1. Displays whether the luggage door opening switch assembly (unlock switch) is on or off.
    2. Use this Data List item to help determine if there is a switch malfunction when the luggage compartment door open function does not operate.
    Ignition Switch
    Power switch on (IG) / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    1. Displays whether the IG power source signal input is on or off.
    2. Use this Data List item to help determine the cause when all smart entry and system/wireless functions do not operate.
    3. If the electrical key transmitter sub-assembly is brought inside the vehicle and the power switch is pressed twice without depressing the brake pedal, the power switch will turn on (IG). At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the ID code box (immobiliser code ECU) are compared, and the S code stored in the ID code box (immobiliser code ECU) and the code stored in the steering lock ECU (steering lock actuator assembly) are compared, and if all codes match, the power source mode is considered on (IG) at that time.
    Unmatched Vehicle-ID
    Key No. (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List).
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. A communication error due to electric wave interference.
    3. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    No Response
    Communication response / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the power switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. If there is wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List.)
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Unmatch Code or Form
    Code format (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    There is an error in the data sent from the electrical key transmitter sub-assembly (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different manufacturer is being used.
    2. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Key Low Battery
    Transmitter battery depleted / Yes or No
    Yes: Transmitter battery depleted
    No: Transmitter battery not depleted
    The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
    Power Save Cnt 10 Min
    Number of times power saving control is activated due to electrical key transmitter sub-assembly being in detection area for 10 minutes or more / 0 to 255
    Within range of 0 to 255
    If the electrical key transmitter sub-assembly is in a vehicle exterior detection area, communication is frequently performed between the vehicle and electrical key transmitter sub-assembly, resulting in an increase in transmitter battery power consumption. To prevent the transmitter battery from becoming fully depleted, if the electrical key transmitter sub-assembly is left in the detection area for 10 minutes or more, the smart entry and start system automatically deactivates the exterior detection area the electrical key transmitter is in. If the doors are locked/unlocked with a wireless operation or by the mechanical key, the system resumes operation.
    Power Save Cnt 5 Days
    Number of times power saving control 1 (vehicle exterior periodic signal transmission stop) is activated due to hybrid system not being started for 5 days or more / 0 to 255
    Within range of 0 to 255
    -
    Power Save Cnt 14 Days
    Number of times power saving control 2 (lock/unlock sensor of front door outside handle assembly of front passenger door disabled) is activated due to hybrid system not being started for 14 days or more / 0 to 255
    Within range of 0 to 255
    -
    #Codes
    Number of trouble codes / Min: 0, Max: 255
    Number of stored DTCs displayed
    -
    ID Code Difference(Resp)
    ID code (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    C Code Difference
    Challenge code (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
    Other potential causes:
    1. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    ID Code Difference
    Wireless ID code (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "ID Code Difference(Resp)" in the Data List.)
    Other potential causes:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. A communication error due to external noise (RF).
    3. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Immobiliser
    Key response to signal from certification ECU (smart key ECU assembly) / OK or NG
    OK: Key responds to signal from certification ECU (smart key ECU assembly)
    NG: Key does not respond to signal from certification ECU (smart key ECU assembly)
    Problems may be caused by the following:
    1. An electrical key transmitter sub-assembly from a different vehicle is being used.
    2. Malfunctions in the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly) or power switch.
    Different Rolling Code
    Rolling code (incorrect or correct) / Yes or No
    Yes: Communication malfunction
    No: Communication normal
    The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different
    Other potential causes:
    1. An electrical key transmitter sub-assembly switch is pressed 100 times or more in a location where the electric waves cannot reach the vehicle.
    2. A communication error due to external noise (RF).
    3. The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning.
    Auto Entry Cancel SW
    Entry cancel function setting / OFF or ON
    Mode status displayed
    ON: Smart entry and start system canceled
    OFF: Smart entry and start system not canceled
    The default setting for the entry cancel function is OFF. If the customer requests that the smart entry and start system functions (locking and unlocking the doors while carrying the electrical key transmitter sub-assembly, etc.) be canceled, the setting can be changed through the customize function (Click here).
    S Code Check
    S code verification result / OK or NG
    OK: S code verification result normal
    NG: S code verification result abnormal
    Problems may be caused by the following:
    1. Registration has not been performed for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).
    2. Malfunctions in the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU).
    L Code Check
    L code verification result / OK or NG
    OK: L code verification result normal
    NG: L code verification result abnormal
    Problems may be caused by the following:
    1. Registration has not been performed for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).
    2. Malfunctions in the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly).
    Unlock Request Receive
    Status of steering unlock command from certification ECU (smart key ECU assembly) / OK or NG
    OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of power switch turned on (ACC) or on (IG), or of hybrid system start operation performed)
    NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (power switch not turned on (ACC) or on (IG), and hybrid system start operation not performed)
    -
    Lock Request Receive
    Status of steering lock command from certification ECU (smart key ECU assembly) / OK or NG
    OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and power switch off)
    NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and power switch off)
    -
    S Code Check (Past)
    S code verification result (past) / OK or NG (Past)
    OK: Verification result normal
    NG (Past): Verification result abnormal (past)
    -
    L Code Check (Past)
    L code verification result (past) / OK or NG (Past)
    OK: Verification confirmed (past)
    NG (Past): Verification not confirmed (past)
    -
    Steering Lock
    State of whether steering lock ECU (steering lock actuator assembly) has determined steering is locked / Set or Unset
    Set: Steering locked
    Unset: Steering unlocked
    -
    Steering Unlock
    State of whether steering lock ECU (steering lock actuator assembly) determined steering is unlocked / Set or Unset
    Set: Steering unlocked
    Unset: Steering locked
    -
    Short in Driver Side Door Oscillators Circuit
    Short in driver side door electrical key antenna circuit / OK or NG
    OK: Driver side door electrical key antenna circuit is normally
    NG: Driver side door electrical key antenna circuit is abnormally
    -
    Short in Front P Side Door Oscillators Circuit
    Short in front passenger side door electrical key antenna circuit / OK or NG
    OK: Front passenger side door electrical key antenna circuit is normally
    NG: Front passenger side door electrical key antenna circuit is abnormally
    -
    Short in D Side Door Oscillators Circuit (Hist)
    Short in driver side door electrical key antenna circuit (history) / OK or NG (Hist)
    OK: Driver side door electrical key antenna circuit was normally
    NG (Hist): Driver side door electrical key antenna circuit was abnormally
    -
    Short in Fr P Side Door Oscillators Circuit (Hist)
    Short in front passenger side door electrical key antenna circuit (history) / OK or NG (Hist)
    OK: Front passenger side door electrical key antenna circuit was normally
    NG (Hist): Front passenger side door electrical key antenna circuit was abnormally
    -
    Door Unlock Mode2
    Door Unlock Mode2 / All or Driver
    Customization status displayed
    -
    Ignition Available Area
    Ignition available area / Front or All
    Customization status displayed
    -
    Parking Wait Time
    Parking wait time / 0.5s, 1.5s, 2.5s or 5s
    Customization status displayed
    -
    B-Dr Opening Operation
    Back door opening operation / Long, Twice, OFF
    Customization status displayed
    -
    Touch Activation Over Threshold
    Consecutive entry lock operation / Active or Not Active
    Customization status displayed
    -
    Wireless Signal Encryption Support
    Wireless Signal Encryption Support / Yes or No
    Customization status displayed
    -
    Key Low Battery Warning
    Low transmitter battery warning / ON or OFF
    Customization status displayed
    -
    Key Left in Vehicle Buz
    Key left in vehicle buzzer sounds / ON or OFF
    Customization status displayed
    -
    Engine Start Indicator
    Hybrid system start indicator lights / ON or OFF
    Customization status displayed
    -
    *: Data from an actual vehicle provided for reference.


    B251338E08

    HINT:
    1. *1: With power switch off, all doors closed, electrical key transmitter sub-assembly not inside vehicle and all doors locked, front door outside handle assembly (unlock sensor) touched.
    2. *2: Approximately 150 ms
    3. *3: With power switch off, all doors closed, electrical key transmitter sub-assembly not inside vehicle and all doors unlocked, front door outside handle assembly (lock sensor) touched.


    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Power switch status / ON or OFF
    ON: Power switch on (ACC)
    OFF: Power switch off
    -
    IG SW
    Power switch status / ON or OFF
    ON: Power switch on (IG)
    OFF: Power switch off
    -
    RR Door Courtesy
    Rear RH door courtesy light switch / OPEN or CLOSE
    OPEN: Rear RH door open
    CLOSE: Rear RH door closed
    -
    RL Door Courtesy
    Rear LH door courtesy light switch / OPEN or CLOSE
    OPEN: Rear LH door open
    CLOSE: Rear LH door closed
    -
    Back Door Courtesy SW
    Back door courtesy light switch / ON or OFF
    ON: Back door open
    OFF: Back door closed
    -
    FR Door Lock Pos
    Front RH door unlock detection switch signal / UNLOCK or LOCK
    UNLOCK: Front RH door unlocked
    LOCK: Front RH door locked
    -
    FR Door Courtesy
    Front RH door courtesy light switch signal / OPEN or CLOSE
    OPEN: Front RH door open
    CLOSE: Front RH door closed
    -
    FL Door Lock Pos
    Front LH door unlock detection switch signal / UNLOCK or LOCK
    UNLOCK: Front LH door unlocked
    LOCK: Front LH door locked
    -
    FL Door Courtesy
    Front LH door courtesy light switch signal / OPEN or CLOSE
    OPEN: Front LH door open
    CLOSE: Front LH door closed
    -
    RR-Door Lock Pos SW
    Rear door RH and LH unlock detection switch signal / ON or OFF
    ON: Rear door RH or LH unlocked
    OFF: Rear door RH and LH locked
    -
    RL-Door Lock Pos SW
    Rear door RH and LH unlock detection switch signal / ON or OFF
    ON: Rear door RH or LH unlocked
    OFF: Rear door RH and LH locked
    -
    Hazard Answer Back
    Hazard answer-back of entry function / ON or OFF
    Customization status displayed
    -
    Open Door Warning
    Open door warning / ON or OFF
    Customization status displayed
    -
    Auto Lock Time
    Automatic lock time / 120 s, 60 s or 30 s
    Customization status displayed
    -
    Wireless Buzzer Resp*
    Buzzer answer-back of entry function / ON or OFF
    Customization status displayed
    -
    Wireless Buzzer Vol*
    Entry door lock buzzer volume / Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0
    Customization status displayed
    -
    1. *: w/ Wireless Buzzer Answer-back Function

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift P Signal
    Shift position P/ON or OFF
    ON: Shift lever in P
    OFF: Shift lever not in P
    1. Use this item to determine if the shift position switch is malfunctioning.
    2. The hybrid system cannot be started when this item is OFF.
    Steering Unlock Switch
    State of steering unlock sensor signal output from steering lock actuator assembly/ON or OFF
    ON: Steering unlocked
    OFF: Steering locked
    1. When the shift lever is in P and the power switch is off, if any door is opened then closed, the steering is locked.
    2. When the key is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks.
    3. The hybrid system cannot be started when the steering unlock signal is off.
    Stop Light Switch1
    State of brake pedal/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The hybrid system cannot be started when this item is OFF.
    3. When this item is malfunctioning, the hybrid system can be started by pressing and holding the power switch for a certain period of time.
    Start Switch1
    Power switch 1 status/ON or OFF
    ON: Power switch pressed
    OFF: Power switch not pressed
    1. If the power switch is pressed for a short time, the display may not change.
    2. Use this item to determine whether the power switch input signal is malfunctioning.
    Start Switch2
    Power switch 2 status/ON or OFF
    ON: Power switch pressed
    OFF: Power switch not pressed
    1. Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.
    2. Behaves the same way as power switch 1.
    Vehicle Speed Signal
    Vehicle being driven or stopped/Stop or Run
    Stop: Vehicle stopped
    Run: Vehicle being driven at 5 km/h (3 mph) or more
    -

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed / Min.: 0, Max.: 255
    Almost the same as actual vehicle speed
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Entry&Start or Main Body / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

    Entry&Start 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Overhead Tuner Power Supply ON
    Door control receiver
    OFF/ON
    -
    Power for P-Seat Sens
    Front door outside handle (for front passenger door)
    OFF/ON
    -
    Multi Channel SW*
    Door control receiver
    CH1/CH2
    -

    1. *: w/ Tire Pressure Warning System

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Door Lock
    Door lock motor
    Unlock/Lock
    -
    Trunk and Back-Door Open
    Operate back door lock motor
    OFF/ON
    -
    Wireless Buzzer
    Wireless door lock buzzer
    OFF/ON
    -