SMART ENTRY AND START SYSTEM (for Entry Function) > Front Passenger Side Door Entry Lock and Unlock Functions do not Operate |

| 1.CHECK POWER DOOR LOCK CONTROL SYSTEM |
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).
|
| ||||
| OK | |
| 2.CHECK WAVE ENVIRONMENT |
![]() |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for front passenger door) and perform an entry function check (Click here).
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
| Result | Proceed to |
| Entry function does not operate normally. | A |
| Entry function operates normally. | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU) |
Disconnect the H11*1, or J11*2 front door outside handle assembly (for front passenger door) connector.
Disconnect the G55 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H11-3 (ANT2) - G55-12 (CG2B) | Always | Below 1 Ω |
| H11-6 (ANT1) - G55-13 (CLG2) | Always | Below 1 Ω |
| H11-5 (B) - G55-16 (POS2) | Always | Below 1 Ω |
| H11-2 (GND) - Body ground | Always | Below 1 Ω |
| H11-3 (ANT2) or G55-12 (CG2B) - Body ground | Always | 10 kΩ or higher |
| H11-6 (ANT1) or G55-13 (CLG2) - Body ground | Always | 10 kΩ or higher |
| H11-5 (B) or G55-16 (POS2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| J11-3 (ANT2) - G55-12 (CG2B) | Always | Below 1 Ω |
| J11-6 (ANT1) - G55-13 (CLG2) | Always | Below 1 Ω |
| J11-5 (B) - G55-16 (POS2) | Always | Below 1 Ω |
| J11-2 (GND) - Body ground | Always | Below 1 Ω |
| J11-3 (ANT2) or G55-12 (CG2B) - Body ground | Always | 10 kΩ or higher |
| J11-6 (ANT1) or G55-13 (CLG2) - Body ground | Always | 10 kΩ or higher |
| J11-5 (B) or G55-16 (POS2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA) |
![]() |
Disconnect the H11*1 or J11*2 front door outside handle assembly (for front passenger door) connector.
Connect the G55 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| H11-5 (B) - H11-2 (GND)*1 J11-5 (B) - J11-2 (GND)*2 | Power switch off → on (IG) | 9 to 14 V → Below 2 V |
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
| H11-3 (ANT2) - H11-6 (ANT1)*1 J11-3 (ANT2) - J11-6 (ANT1)*2 | Procedure:
| 2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
| *A | for LHD |
| *B | for RHD |
| *1 | Waveform |
| *a | Front view of wire harness connector (to Front Door Outside handle assembly (for front passenger door)) |
|
| ||||
| OK | |
| 5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) |
Temporarily replace the front door outside handle assembly (for front passenger door) with a new or known good one (Click here).
| NEXT | |
| 6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION) |
Check that the entry functions operate normally (Click here).
|
| ||||
| OK | ||
| ||