Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > Room Oscillator does not Recognize Key

for Preparation Click here


DESCRIPTION

If code verification cannot be performed in the vehicle interior, there may be problems with the communication between the vehicle (indoor electrical key antenna assembly (front floor), (steering column) or (rear floor)) and electrical key transmitter sub-assembly, or the certification ECU (smart key ECU assembly) may be malfunctioning. When the electrical key transmitter sub-assembly is brought into the vehicle, verification of the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) is performed. If verification cannot be performed or the codes do not match, the power switch cannot be turned on (IG) and the hybrid system cannot be started.
When a door is unlocked and the electrical key transmitter sub-assembly is brought into the vehicle, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna assembly which transmits radio waves to detect the electrical key transmitter sub-assembly. If the electrical key transmitter sub-assembly recognizes that it is in the detection area, it responds with the key ID code. This information is received by the indoor electrical key antenna and then sent to the certification ECU (smart key ECU assembly).

WIRING DIAGRAM


B300397E05


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the power switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  4. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
  5. The indoor electrical key antenna assemblies have an antenna coil between each two CLG terminals.
  6. The door control receiver is also related to interior verification.

1.CHECK ENTRY DOOR LOCK OPERATION
  1. Check that the entry lock and unlock functions operate for each door (Click here).

    OK:
    All door entry lock and unlock functions operate normally.

    HINT:
    If the door control receiver is defective, code verification does not begin in the cabin and the entry functions do not operate.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


2.CHECK PUSH START FUNCTION


    B296539E01
  1. Remove the transmitter battery of the electrical key transmitter sub-assembly (Click here).

  1. With the brake pedal depressed, face the logo side of the electrical transmitter sub-assembly towards the power switch, hold the transmitter near the power switch and then press the power switch.

  1. When operating the power switch, check whether the hybrid system starts.

    HINT:
    1. When the electrical key transmitter sub-assembly cannot be verified even though it is inside the detection area, the hybrid system start check can be performed by removing the transmitter battery from the electrical key transmitter sub-assembly and holding the electrical key transmitter sub-assembly near the power switch.
    2. If the hybrid system cannot be started when performing this inspection, the certification ECU (smart key ECU assembly), steering lock ECU (Steering lock actuator assembly) or ID code box (immobiliser code ECU) may be malfunctioning.

    OK:
    Hybrid system starts.

    Text in Illustration 
    *1
    Power Switch
    *2
    Electrical Key Transmitter Sub-assembly



NG
GO TO SMART ENTRY AND START SYSTEM (FOR START FUNCTION) (Click here)
OK


3.CHECK WAVE ENVIRONMENT
  1. Install the transmitter battery to the electrical key transmitter sub-assembly (Click here).

  1. Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform a smart entry and start system check (Click here).

    NOTICE:
    Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

  1. Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (steering column) and perform a smart entry and start system check (Click here)

    HINT:
    Check that the customize status of the "Ignition Available Area" has been "All".

    NOTICE:
    Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key antenna assembly (steering column).

  1. Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (rear floor) and perform a smart entry and start system check (Click here)

    HINT:
    Check that the customize status of the "Ignition Available Area" has been "All".

    NOTICE:
    Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 3 indoor electrical key antenna assembly (rear floor).

HINT:
  1. As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to the each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
  2. If the problem only occurs in specific places or at specific times, wave interference may be the cause of the problem. Also, the vehicle may be have the effects of wave interference with the parts installed by the dealer. As a result, when parts have been installed by the dealer, it may be necessary to remove those parts before inspecting the vehicle.
  3. There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
  4. If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

Result:
Result
Proceed to
System cannot be operated
A
System can be operated
B



B
AFFECTED BY WAVE INTERFERENCE
A


4.CHECK KEY DIAGNOSTIC MODE


  1. Check the following antennas in the key diagnostic mode (Click here).



      B296517E01
    1. Check the No. 1 indoor electrical key antenna assembly (front floor).
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    2. B300410E01
    3. Check the No. 2 indoor electrical key antenna assembly (steering column).
      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    4. B296518E01
    5. Check the No. 3 indoor electrical key antenna (rear floor):
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

      HINT:
      1. If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.
      2. It is possible to check which indoor electrical key antenna assembly (front floor, steering column or rear floor) is operating by the sounding of the buzzer.
      3. If the buzzer does not sound for any indoor electrical key antenna assemblies, the certification ECU (smart key ECU assembly) circuit may have a malfunction.

      OK:
      Wireless door lock buzzer sounds.

      Result:
      Result
      Proceed to
      Front floor operation check fails
      A
      Steering column operation check fails
      B
      Rear floor operation check fails
      C
      All operation checks are normal
      D



B
Go to step 9

C
Go to step 13

D
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
A


5.CHECK HARNESS AND CONNECTOR (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)
  1. Disconnect the G51 No. 1 indoor electrical key antenna assembly (front floor) connector.

  1. Disconnect the G55 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G51-1 (ANTE5) - G55-11 (CLG5)
    Always
    Below 1 Ω
    G51-3 (CLGB) - G55-10 (CG5B)
    Always
    Below 1 Ω
    G51-1 (ANTE5) or G55-11 (CLG5) - Body ground
    Always
    10 kΩ or higher
    G51-3 (CLGB) or G55-10 (CG5B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA)


    B250988E47
  1. Disconnect the G51 No. 1 indoor electrical key antenna assembly (front floor) connector.

  1. Connect the G55 certification ECU (smart key ECU assembly) connector.

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    G51-1 (ANTE5) - G51-3 (CLGB)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform)

    Text in Illustration 
    *1
    Waveform
    *a
    Front view of wire harness connector
    (to No. 1 Indoor Electrical Key Antenna [Front Floor])
    *b
    Within approximately 30 seconds from when the door is closed
    *c
    After approximately 30 seconds from when the door is closed



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


7.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
  1. Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new or known good one (Click here).


NEXT


8.CHECK KEY DIAGNOSTIC MODE


  1. Check the following antenna in the key diagnostic mode (Click here).



      B296517E01
    1. Check the No. 1 indoor electrical key antenna assembly (front floor).
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

      OK:
      Wireless door lock buzzer sounds.

      Text in Illustration 
      *a
      Inspection Point



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR) WAS DEFECTIVE) 

9.CHECK HARNESS AND CONNECTOR (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)
  1. Disconnect the G52 No. 2 indoor electrical key antenna assembly (steering column) connector.

  1. Disconnect the G53 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G52-1 (ANTE6) - G53-14 (CLG6)
    Always
    Below 1 Ω
    G52-3 (CLGB) - G53-5 (CG6B)
    Always
    Below 1 Ω
    G52-1 (ANTE6) or G53-14 (CLG6) - Body ground
    Always
    10 kΩ or higher
    G52-3 (CLGB) or G53-5 (CG6B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA)


    B250988E48
  1. Disconnect the G52 No. 2 indoor electrical key antenna assembly (steering column) connector.

  1. Connect the G53 certification ECU (smart key ECU assembly) connector.

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    G52-1 (ANTE6) - G52-3 (CLGB)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform)

    Text in Illustration 
    *1
    Waveform
    *a
    Front view of wire harness connector
    (to No. 2 Indoor Electrical Key Antenna [Steering Column])
    *b
    Within approximately 30 seconds from when the door is closed
    *c
    After approximately 30 seconds from when the door is closed



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


11.REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (STEERING COLUMN)
  1. Temporarily replace the No. 2 indoor electrical key antenna assembly (steering column) with a new or known good one (Click here).


NEXT


12.CHECK KEY DIAGNOSTIC MODE


  1. Check the following antenna in the key diagnostic mode (Click here).



      B300410E01
    1. Check the No. 2 indoor electrical key antenna assembly (steering column).
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

      OK:
      Wireless door lock buzzer sounds.

      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Inspection Point



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (STEERING COLUMN) WAS DEFECTIVE) 

13.CHECK HARNESS AND CONNECTOR (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY - CERTIFICATION ECU)
  1. Disconnect the M16 No. 3 indoor electrical key antenna assembly (rear floor) connector.

  1. Disconnect the G53 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M16-1 (ANTE7) - G53-4 (CLG7)
    Always
    Below 1 Ω
    M16-3 (CLGB) - G53-3 (CG7B)
    Always
    Below 1 Ω
    M16-1 (ANTE7) or G53-4 (CLG7) - Body ground
    Always
    10 kΩ or higher
    M16-3 (CLGB) or G53-3 (CG7B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA)


    B250988E49
  1. Disconnect the M16 No. 3 indoor electrical key antenna assembly (rear floor) connector.

  1. Connect the G53 certification ECU (smart key ECU assembly) connector.

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    M16-1 (ANTE7) - M16-3 (CLGB)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform)

    Text in Illustration 
    *1
    Waveform
    *a
    Front view of wire harness connector
    (to No. 3 Indoor Electrical Key Antenna [Rear Floor])
    *b
    Within approximately 30 seconds from when the door is closed
    *c
    After approximately 30 seconds from when the door is closed



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


15.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
  1. Temporarily replace the No. 3 indoor electrical key antenna assembly (rear floor) with a new or known good one (Click here).


NEXT


16.CHECK SELF DIAGNOSTIC MODE


  1. Check the following antenna in the key diagnostic mode (Click here).



      B296518E01
    1. Check the No. 3 indoor electrical key antenna assembly (rear floor).
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.

      OK:
      Wireless door lock buzzer sounds.

      Text in Illustration 
      *a
      Inspection Point



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))