Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  2. Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.
  3. Turn the power switch off before inspecting CAN bus lines for a ground short.
  4. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  5. This section describes the standard values for all CAN related components.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.


CAN JUNCTION CONNECTOR LH (for LHD)


  1. Check the CAN junction connector LH (instrument panel wire side).



    1. Connection diagram


      C251171E01


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN Junction Connector LH (Instrument Panel Wire Side))
      *b
      to Main Body ECU (Multiplex Network Body ECU)
      (for V Bus)
      *c
      to Power Steering ECU Assembly
      (for V Bus)
      *d
      to DLC3
      (for V Bus)
      *e
      to CAN Junction Connector RH
      (for V Bus)
      *f
      to Hybrid Vehicle Control Computer Assembly
      (for V Bus)

    2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      G71-1 (CANH)
      R
      Main body ECU (Multiplex network body ECU)
      (for V bus)
      G71-12 (CANL)
      W
      G71-2 (CANH)
      LG
      Power steering ECU assembly
      (for V bus)
      G71-13 (CANL)
      W
      G71-3 (CANH)
      GR
      DLC3
      (for V bus)
      G71-14 (CANL)
      W
      G71-4 (CANH)
      SB
      CAN junction connector RH
      (for V bus)
      G71-15 (CANL)
      W
      G71-5 (CANH)
      BE
      Hybrid vehicle control computer assembly
      (for V bus)
      G71-16 (CANL)
      W



  2. Check the CAN junction connector LH (engine room main wire side).



    1. Connection diagram


      C251171E02


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN Junction Connector LH (Engine Room Main Wire Side))
      *b
      to ECM
      (for V Bus)
      *c
      to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
      (for V Bus)
      -
      -

    2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      A51-9 (CANH)
      L
      ECM
      (for V bus)
      A51-20 (CANL)
      W
      A51-10 (CANH)
      B
      Brake booster with master cylinder assembly (Skid control ECU)
      (for V bus)
      A51-21 (CANL)
      W


CAN JUNCTION CONNECTOR LH (for RHD)


  1. Check the CAN junction connector LH (instrument panel wire side).



    1. Connection diagram


      C251171E03


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN Junction Connector LH (Instrument Panel Wire Side))
      *b
      to Main Body ECU (Multiplex Network Body ECU)
      (for V Bus)
      *c
      to Smart Key ECU Assembly (Certification ECU)
      (for V Bus)
      *d
      to CAN Junction Connector RH
      (for V Bus)
      *e
      to Hybrid Vehicle Control Computer Assembly
      (for V Bus)
      -
      -

    2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      G71-1 (CANH)
      R
      Main body ECU (Multiplex network body ECU)
      (for V bus)
      G71-12 (CANL)
      W
      G71-3 (CANH)
      L
      Smart key ECU assembly (Certification ECU)
      (for V bus)
      G71-14 (CANL)
      W
      G71-4 (CANH)
      SB
      CAN junction connector RH
      (for V bus)
      G71-15 (CANL)
      W
      G71-5 (CANH)
      BE
      Hybrid vehicle control computer assembly
      (for V bus)
      G71-16 (CANL)
      W



  2. Check the CAN junction connector LH (engine room main wire side).



    1. Connection diagram


      C251171E02


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN Junction Connector LH (Engine Room Main Wire Side))
      *b
      to ECM
      (for V Bus)
      *c
      to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
      (for V Bus)
      -
      -

    2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      A51-9 (CANH)
      L
      ECM
      (for V bus)
      A51-20 (CANL)
      W
      A51-10 (CANH)
      B
      Brake booster with master cylinder assembly (Skid control ECU)
      (for V bus)
      A51-21 (CANL)
      W


CAN JUNCTION CONNECTOR RH (for LHD)


  1. Check the CAN junction connector RH.



    1. Connection diagram


      C251171E04


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN Junction Connector RH)
      *b
      to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
      (for V Bus)
      *c
      to Smart Key ECU Assembly (Certification ECU)
      (for V Bus)
      *d
      to Airbag Sensor Assembly
      (for V Bus)
      *e
      to Combination Meter Assembly
      (for V Bus)
      *f
      to Air Conditioning Amplifier Assembly
      (for V Bus)
      *g
      to CAN Junction Connector LH
      (for V Bus)
      -
      -

    2. Check the connection diagram of the components which are connected to the CAN junction connector RH.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      G72-1 (CANH)
      P
      Spiral cable with sensor sub-assembly (Steering sensor)
      (for V bus)
      G72-12 (CANL)
      W
      G72-3 (CANH)
      L
      Smart key ECU assembly (Certification ECU)
      (for V bus)
      G72-14 (CANL)
      W
      G72-4 (CANH)
      B
      Airbag sensor assembly
      (for V bus)
      G72-15 (CANL)
      W
      G72-7 (CANH)
      G
      Combination meter assembly
      (for V bus)
      G72-18 (CANL)
      W
      G72-8 (CANH)
      V
      Air conditioning amplifier assembly
      (for V bus)
      G72-19 (CANL)
      W
      G72-10 (CANH)
      SB
      CAN junction connector LH
      (for V bus)
      G72-21 (CANL)
      W


CAN JUNCTION CONNECTOR RH (for RHD)


  1. Check the CAN junction connector RH.



    1. Connection diagram


      C251171E05


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN Junction Connector RH)
      *b
      to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
      (for V Bus)
      *c
      to Airbag Sensor Assembly
      (for V Bus)
      *d
      to Power Steering ECU Assembly
      (for V Bus)
      *e
      to Combination Meter Assembly
      (for V Bus)
      *f
      to Air Conditioning Amplifier Assembly
      (for V Bus)
      *g
      to CAN Junction Connector LH
      (for V Bus)
      *h
      to DLC3
      (for V Bus)

    2. Check the connection diagram of the components which are connected to the CAN junction connector RH.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      G72-1 (CANH)
      P
      Spiral cable with sensor sub-assembly (Steering sensor)
      (for V bus)
      G72-12 (CANL)
      W
      G72-4 (CANH)
      B
      Airbag sensor assembly
      (for V bus)
      G72-15 (CANL)
      W
      G72-6 (CANH)
      LG
      Power steering ECU assembly
      (for V bus)
      G72-17 (CANH)
      W
      G72-7 (CANH)
      G
      Combination meter assembly
      (for V bus)
      G72-18 (CANL)
      W
      G72-8 (CANH)
      V
      Air conditioning amplifier assembly
      (for V bus)
      G72-19 (CANL)
      W
      G72-10 (CANH)
      SB
      CAN junction connector LH
      (for V bus)
      G72-21 (CANL)
      W
      G72-11 (CANH)
      GR
      DLC3
      (for V bus)
      G72-22 (CANH)
      W


CAN JUNCTION CONNECTOR LH


  1. Check the CAN junction connector LH (engine room main wire side).



    1. Connection diagram


      C251171E06


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN Junction Connector LH (Engine Room Main Wire Side))
      *b
      to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
      (for Sub Bus 15)
      *c
      to ECM
      (for Sub Bus 15)
      -
      -

    2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      A51-1 (CANH)
      L
      Brake booster with master cylinder assembly (Skid control ECU)
      (for Sub bus 15)
      A51-12 (CANL)
      W
      A51-3 (CANH)
      B
      ECM
      (for Sub bus 15)
      A51-14 (CANL)
      W



  2. Check the CAN junction connector LH (instrument panel wire side).



    1. Connection diagram


      C251171E07


      Text in Illustration 
      *a
      Front view of wire harness connector
      (to CAN Junction Connector LH (Instrument Panel Wire Side))
      *b
      to Hybrid Vehicle Control Computer Assembly
      (for Sub Bus 15)

    2. Check the connection diagram of the components which are connected to the CAN junction connector LH.

      Terminal No. (Symbol)
      Wiring Color
      Connected to
      G71-10 (CANH)
      R
      Hybrid vehicle control computer assembly
      (for Sub bus 15)
      G71-21 (CANL)
      W


DLC3
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. C210421E69
  3. Measure the resistance according to the value(s) in the table below.
    Text in Illustration 
    *1
    DLC3

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G4-6 (CANH) - G4-14 (CANL)
    GR - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    G4-6 (CANH) - G4-4 (CG)
    GR - P
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G4-14 (CANL) - G4-4 (CG)
    W - P
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G4-6 (CANH) - G4-16 (BAT)
    GR - SB
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G4-14 (CANL) - G4-16 (BAT)
    W - SB
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY

C322424E01


Text in Illustration 
*a
Component without harness connected
(Hybrid Vehicle Control Computer Assembly)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. A204446E85
  3. Disconnect the G81 hybrid vehicle control computer assembly connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Hybrid Vehicle Control Computer Assembly)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V Bus Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G81-25 (CA1H) - G81-24 (CA1L)
    BE - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    G81-25 (CA1H) - G80-6 (E1)
    BE - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G81-24 (CA1L) - G80-6 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G81-25 (CA1H) - G81-3 (BATT)
    BE - BE
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G81-24 (CA1L) - G81-3 (BATT)
    W - BE
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher

    Sub Bus 15 Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G81-31 (CA3P) - G81-30 (CA3N)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    G81-31 (CA3P) - G80-6 (E1)
    R - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G81-30 (CA3N) - G80-6 (E1)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G81-31 (CA3P) - G81-3 (BATT)
    R - BE
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G81-30 (CA3N) - G81-3 (BATT)
    W - BE
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


ECM

C248538E03


Text in Illustration 
*A
for LHD
*B
for RHD
*a
Component without harness connected
(ECM)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the A40 and C9 or C10 ECM connectors.


    C258725E01


    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V Bus Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A40-13 (CANH) - A40-26 (CANL)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    A40-13 (CANH) - C10-16 (E1)*1
    A40-13 (CANH) - C9-16 (E1)*2
    L - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A40-26 (CANL) - C10-16 (E1)*1
    A40-26 (CANL) - C9-16 (E1)*2
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A40-13 (CANH) - A40-1 (BATT)
    L - Y
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A40-26 (CANL) - A40-1 (BATT)
    W - Y
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher

    Sub Bus 15 Main Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A40-12 (CANP) - A40-25 (CANN)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    A40-12 (CANP) - C10-16 (E1)*1
    A40-12 (CANP) - C9-16 (E1)*2
    B - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A40-25 (CANN) - C10-16 (E1)*1
    A40-25 (CANN) - C9-16 (E1)*2
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A40-12 (CANP) - A40-1 (BATT)
    B - Y
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A40-25 (CANN) - A40-1 (BATT)
    W - Y
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher

    *1: for LHD
    *2: for RHD


BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

C156569E06


Text in Illustration 
*a
Component without harness connected
(Brake Booster with Master Cylinder Assembly (Skid Control ECU))
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. C249762E50
  3. Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    V Bus Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A41-37 (CA1H) - A41-38 (CA1L)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    A41-37 (CA1H) - A41-28 (GND)
    B - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A41-38 (CA1L) - A41-28 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A41-37 (CA1H) - A41-14 (BI)
    B - W
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A41-38 (CA1L) - A41-14 (BI)
    W - W
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher

    Sub Bus 15 Branch Lines 
    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A41-35 (CA2H) - A41-34 (CA2L)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    A41-35 (CA2H) - A41-28 (GND)
    L - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A41-34 (CA2L) - A41-28 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    A41-35 (CA2H) - A41-14 (BI)
    L - W
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    A41-34 (CA2L) - A41-14 (BI)
    W - W
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


AIRBAG SENSOR ASSEMBLY

C219162E02


Text in Illustration 
*a
Component without harness connected
(Airbag Sensor Assembly)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the G18 airbag sensor assembly connector.


    C188802E24


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G18-13 (CANH) - G18-22 (CANL)
    B - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    G18-13 (CANH) - G18-25 (E1)
    B - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G18-22 (CANL) - G18-25 (E1)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G18-13 (CANH) - G4-16 (BAT)
    B - SB
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G18-22 (CANL) - G4-16 (BAT)
    W - SB
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B281049E21


Text in Illustration 
*A
Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) with 1 connector)
*B
for LHD
*C
for RHD
-
-
*1
Main Body ECU (Multiplex Network Body ECU)
-
-

B297238E03


Text in Illustration 
*A
Component without harness connected
(Main Body ECU (Multiplex Network Body ECU) with 2 connectors)
-
-
*1
Main Body ECU (Multiplex Network Body ECU)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the G59 main body ECU (multiplex network body ECU) connector.


    C250555E02


    Text in Illustration 
    *1
    DLC3
    -
    -
    *a
    Front view of wire harness connector
    (to Main Body ECU (Multiplex Network Body ECU))
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G59-14 (CANH) - G59-13 (CANL)
    R - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    G59-14 (CANH) - G4-4 (CG)
    R - P
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G59-13 (CANL) - G4-4 (CG)
    W - P
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G59-14 (CANH) - G4-16 (BAT)
    R - SB
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G59-13 (CANL) - G4-16 (BAT)
    W - SB
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING SENSOR)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. C259243E01
  3. Disconnect the G30 spiral cable with sensor sub-assembly (steering sensor) connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable with Sensor Sub-assembly (Steering Sensor))

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G30-4 (CANH) - G30-3 (CANL)
    P - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    G30-4 (CANH) - G30-2 (ESS)
    P - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G30-3 (CANL) - G30-2 (ESS)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G30-4 (CANH) - G30-6 (BAT)
    P - B
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G30-3 (CANL) - G30-6 (BAT)
    W - B
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


POWER STEERING ECU ASSEMBLY

C240518E04


Text in Illustration 
*a
Component without harness connected
(Power Steering ECU Assembly)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. Disconnect the A33 and G6 power steering ECU assembly connectors.


    C258818E01


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)
    -
    -

  3. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G6-7 (CANH) - G6-8 (CANL)
    LG - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    G6-7 (CANH) - A33-2 (PGND)
    LG - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G6-8 (CANL) - A33-2 (PGND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G6-7 (CANH) - A33-1 (PIG)
    LG - W
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G6-8 (CANL) - A33-1 (PIG)
    W - W
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


SMART KEY ECU ASSEMBLY (CERTIFICATION ECU)

B264892E99


Text in Illustration 
*a
Component without harness connected
(Smart Key ECU Assembly (Certification ECU))
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. C240538E10
  3. Disconnect the G77 and G79 smart key ECU assembly (certification ECU) connectors.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Smart Key ECU Assembly (Certification ECU))

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G79-14 (CANH) - G79-15 (CANL)
    L - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    G79-14 (CANH) - G77-11 (E)
    L - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G79-15 (CANL) - G77-11 (E)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G79-14 (CANH) - G77-2 (+B)
    L - B
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G79-15 (CANL) - G77-2 (+B)
    W - B
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


COMBINATION METER ASSEMBLY

C251168E01


Text in Illustration 
*a
Component without harness connected
(Combination Meter Assembly)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. C256258E02
  3. Disconnect the G1 combination meter assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G1-31 (CANH) - G1-32 (CANL)
    G - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    108 to 132 Ω
    G1-31 (CANH) - G1-20 (ET)
    G - BR
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G1-32 (CANL) - G1-20 (ET)
    W - BR
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G1-31 (CANH) - G1-1 (B)
    G - L
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G1-32 (CANL) - G1-1 (B)
    W - L
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER ASSEMBLY

E226604E16


Text in Illustration 
*a
Component without harness connected
(Air Conditioning Amplifier Assembly)
-
-
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



  2. C256258E03
  3. Disconnect the G34 air conditioning amplifier assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Conditioning Amplifier Assembly)

  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G34-11 (CANH) - G34-12 (CANL)
    V - W
    HIGH-level CAN bus line - LOW-level CAN bus line
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω
    G34-11 (CANH) - G34-14 (GND)
    V - W-B
    HIGH-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G34-12 (CANL) - G34-14 (GND)
    W - W-B
    LOW-level CAN bus line - Ground
    Cable disconnected from negative (-) auxiliary battery terminal
    200 Ω or higher
    G34-11 (CANH) - G34-21 (B)
    V - BE
    HIGH-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G34-12 (CANL) - G34-21 (B)
    W - BE
    LOW-level CAN bus line - Auxiliary battery positive (+)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher