DTC P0705-757 Transmission Range Sensor Circuit |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0705 | 757 | Logical inconsistency in shift sensor output values |
|

| 1.READ VALUE USING INTELLIGENT TESTER (SHIFT POSITION) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Sensor SW - P, Shift Sensor SW - R, Shift Sensor SW - N, Shift Sensor SW - DB1, Shift Sensor SW - DB2, Shift Sensor SW - PR, Shift Sensor SW - PNB.
While slowly moving the shift lever from P to B, then back to P, read the Data List (shift position) displayed on the intelligent tester.
| ECU Data List | Shift Position | ||||
| P | R | N | D | B | |
| Shift Sensor SW-P | ON | OFF | OFF | OFF | OFF |
| Shift Sensor SW-R | OFF | ON | OFF | OFF | OFF |
| Shift Sensor SW-PR | ON | ON | OFF | OFF | OFF |
| Shift Sensor SW-N | OFF | OFF | ON | OFF | OFF |
| Shift Sensor SW-DB1 | OFF | OFF | OFF | ON | ON |
| Shift Sensor SW-DB2 | OFF | OFF | OFF | ON | ON |
| Shift Sensor SW-PNB | ON | OFF | ON | OFF | ON |
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
Turn the power switch off.
|
| ||||
| OK | |
| 2.CHECK FOR INTERMITTENT PROBLEMS |
|
| ||||
| OK | ||
| ||
| 3.CHECK SHIFT LEVER POSITION SENSOR |
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A72-21 (P) - Body ground | Power switch on (IG) Shift lever in P | 11 to 14 V |
| A72-21 (P) - Body ground | Power switch on (IG) Any position except shift lever in P | 0 to 1.5 V |
| A72-15 (R) - Body ground | Power switch on (IG) Shift lever in R | 11 to 14 V |
| A72-15 (R) - Body ground | Power switch on (IG) Any position except shift lever in R | 0 to 1.5 V |
| A72-17 (PR) - Body ground | Power switch on (IG) Shift lever in P or R | 11 to 14 V |
| A72-17 (PR) - Body ground | Power switch on (IG) Any position except shift lever in P and R | 0 to 1.5 V |
| A72-20 (N) - Body ground | Power switch on (IG) Shift lever in N | 11 to 14 V |
| A72-20 (N) - Body ground | Power switch on (IG) Any position except shift lever in N | 0 to 1.5 V |
| A72-26 (DB1) - Body ground | Power switch on (IG) Shift lever in D or B | 11 to 14 V |
| A72-26 (DB1) - Body ground | Power switch on (IG) Any position except shift lever in D and B | 0 to 1.5 V |
| A72-14 (DB2) - Body ground | Power switch on (IG) Shift lever in D or B | 11 to 14 V |
| A72-14 (DB2) - Body ground | Power switch on (IG) Any position except shift lever in D and B | 0 to 1.5 V |
| A72-34 (PNB) - Body ground | Power switch on (IG) Shift lever in P, N or B | 11 to 14 V |
| A72-34 (PNB) - Body ground | Power switch on (IG) Any position except shift lever in P, N and B | 0 to 1.5 V |
| *a | Component with harness connected (Hybrid Vehicle Control ECU) |
Turn the power switch off.
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) |
Disconnect the shift lever position sensor connector.
Turn the power switch on (IG).
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C23-7 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Shift Lever Position Sensor) |
Turn the power switch off.
Connect the shift lever position sensor connector.
|
| ||||
| OK | |
| 5.INSPECT SHIFT LEVER POSITION SENSOR |
Disconnect the shift lever position sensor connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C23-7 (+B) - C23-3 (PR) | Shift lever in P | Below 1 Ω |
| C23-7 (+B) - C23-4 (PNB) | Below 1 Ω | |
| C23-7 (+B) - C23-8 (P) | Below 1 Ω | |
| C23-7 (+B) - C23-1 (DB1), C23-2 (N), C23-6 (DB2) and C23-9 (R) | 10 kΩ or higher | |
| C23-7 (+B) - C23-3 (PR) | Shift lever in R | Below 1 Ω |
| C23-7 (+B) - C23-9 (R) | Below 1 Ω | |
| C23-7 (+B) - C23-1 (DB1), C23-2 (N), C23-4 (PNB), C23-6 (DB2) and C23-8 (P) | 10 kΩ or higher | |
| C23-7 (+B) - C23-2 (N) | Shift lever in N | Below 1 Ω |
| C23-7 (+B) - C23-4 (PNB) | Below 1 Ω | |
| C23-7 (+B) - C23-1 (DB1), C23-3 (PR), C23-6 (DB2), C23-8 (P) and C23-9 (R) | 10 kΩ or higher | |
| C23-7 (+B) - C23-1 (DB1) | Shift lever in D | Below 1 Ω |
| C23-7 (+B) - C23-6 (DB2) | Below 1 Ω | |
| C23-7 (+B) - C23-2 (N), C23-3 (PR), C23-4 (PNB), C23-8 (P) and C23-9 (R) | 10 kΩ or higher | |
| C23-7 (+B) - C23-1 (DB1) | Shift lever in B | Below 1 Ω |
| C23-7 (+B) - C23-4 (PNB) | Below 1 Ω | |
| C23-7 (+B) - C23-6 (DB2) | Below 1 Ω | |
| C23-7 (+B) - C23-2 (N), C23-3 (PR), C23-8 (P) and C23-9 (R) | 10 kΩ or higher |
| *a | Component without harness connected (Shift Lever Position Sensor) |
Connect the shift lever position sensor connector.
|
| ||||
| OK | ||
| ||