Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A0F-238    Engine Failed to Start

for Preparation Click here


DESCRIPTION

If the power management control ECU detects that the engine or transaxle gear has seized, the power management control ECU will perform fail-safe control. Also, if a substance or object is preventing the engine or transaxle internal components from rotating, the power management control ECU will perform fail-safe control.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A0F
238
Engine does not start even though it is being cranked (transaxle input malfunction [engine system])
  1. Hybrid vehicle transaxle assembly
  2. Transmission input damper assembly
  3. Power management control ECU
  4. Engine

A217594E02


INSPECTION PROCEDURE

HINT:
  1. A seized engine, mechanical malfunction of the hybrid vehicle transaxle can be suspected.
  2. If this DTC is output, the engine or transaxle gear may be seized. Be sure to check the level of the engine oil, automatic transmission fluid (ATF) and coolant before inspection.
  3. After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. While driving the vehicle at a speed of 20 km/h or more in EV mode, depress the accelerator pedal to start the engine, and drive the vehicle for 3 seconds or more.*1
      1. *1: When the HV system is normal, the engine starts when the accelerator pedal is depressed halfway or more. If the HV system is malfunctioning, the engine may not start. Even in this case, if you drive the vehicle at a speed of 12 mph (20 km/h) or more in EV mode for 3 seconds or more, you can confirm this DTC.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Only P0A0F-238 is output or P0A0F-238 and DTCs other than P0A1D are also output.
    A
    P0A1D (Hybrid Powertrain Control Module) is output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (P0A1D) (Click here)
A


2.CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)
  1. Check that the shift lever is in the P position.

  1. Lift up the vehicle.

  1. Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

    CAUTION:
    Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.

    NOTICE:
    Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.

    OK:
    The crankshaft rotates smoothly.

  1. Lower the vehicle.



NG
Go to step 7
OK


3.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


4.CHECK ENGINE RACING
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Generator (MG1) Rev, Engine Revolution.

  1. Read the Data List.



    A212091E01
  1. While the READY indicator is on, fully depress the accelerator pedal for 10 seconds.

    OK:
    Generator (MG1) Rev increases to approximately 3.6 times that of Engine Revolution.

    HINT:
    Refer to the graph for Data List confirmation of "Generator (MG1) Rev" and " Engine Revolution".
    Data List
    ENGINE REV
    MG1 REV
    Reference Value
    Approximately 1000 rpm
    Approximately 3600 rpm
    Approximately 1500 rpm
    Approximately 5400 rpm
    Approximately 2500 rpm
    Approximately 9000 rpm

  1. Turn the power switch off.



NG
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)
OK


5.CHECK CREEP MOVEMENT
  1. Turn the power switch on (READY).

  1. Depress the brake pedal, move the shift lever to D, and release the brake pedal.

    OK:
    The wheels turn (the vehicle creeps forward).

  1. Turn the power switch off.



NG
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)
OK


6.CHECK ENGINE SPEED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Motor (MG2) Revolution, Generator (MG1) Rev, Engine Revolution.

  1. Read the Data List.

  1. Move the shift lever to D.

  1. Fully depress the accelerator pedal to accelerate the vehicle from a stop.

    NOTICE:
    Perform this test only in an appropriate safe location, in accordance with all local laws.

    OK:
    The difference between Engine Revolution and 0.28 X Generator (MG1) Rev + 0.27 X Motor (MG2) Revolution is 500 rpm or more and it is maintained for 1 second.

  1. Turn the power switch off.



NG
REPLACE TRANSMISSION INPUT DAMPER ASSEMBLY (Click here)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

7.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
  1. Lift up the vehicle.

  1. Move the shift lever to N.

  1. Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

    CAUTION:
    Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.

    NOTICE:
    Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.

    OK:
    The crankshaft rotates smoothly.

  1. Lower the vehicle.



NG
REPAIR OR REPLACE ENGINE
OK

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY (Click here)