Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A1A-151    Generator Control Module

DTC    P0A1A-155    Generator Control Module

DTC    P0A1A-156    Generator Control Module

DTC    P0A1A-166    Generator Control Module

DTC    P0A1A-658    Generator Control Module

DTC    P0A1A-659    Generator Control Module

DTC    P0A1A-791    Generator Control Module

DTC    P0A1B-163    Drive Motor "A" Control Module

DTC    P0A1B-164    Drive Motor "A" Control Module

DTC    P0A1B-192    Drive Motor "A" Control Module

DTC    P0A1B-193    Drive Motor "A" Control Module

DTC    P0A1B-198    Drive Motor "A" Control Module

DTC    P0A1B-511    Drive Motor "A" Control Module

DTC    P0A1B-512    Drive Motor "A" Control Module

DTC    P0A1B-661    Drive Motor "A" Control Module

DTC    P0A1B-786    Drive Motor "A" Control Module

DTC    P0A1B-794    Drive Motor "A" Control Module

for Preparation Click here


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and it will set DTCs when it detects malfunctions.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A1A
151
Run pulse signal cycle deviation or stop
Inverter with converter assembly
155
A/D converter error
156
CPU ROM-RAM error
166
R/D converter NM stop error
658
ALU error
659
Communication error (from MG1 to MG2)
791
R/D converter communication error
P0A1B
163
IPM positive power source error
164
IPM negative power source error
192
A/D converter error
193
CPU ROM-RAM error
198
R/D converter NM stop error
511
Standard voltage for analog signal offset
512
Standard voltage for analog signal error
661
Communication error (from MG2 to MG1)
786
ALU error
794
R/D converter communication error

INSPECTION PROCEDURE

HINT:
  1. If DTC P0A1A-151, P0A1A-155, P0A1A-658, P0A1A-659, P0A1A-791 DTC P0A1B-163, P0A1B-164, P0A1B-192, P0A1B-511, P0A1B-512, P0A1B-661, P0A1B-786 or P0A1B-794 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the power switch on (IG) and wait for 5 seconds or more.
  2. If DTC P0A1A-156or P0A1B-193 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the power switch on (IG) and wait for 1 minute or more.
  3. If DTC P0A1A-166 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the power switch on (READY).
    2. With the vehicle stopped and the shift lever in P, depress the accelerator pedal and start the engine.
    3. Depress the accelerator pedal and keep the engine running for 30 seconds or more.
  4. If DTC P0A1B-198 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the power switch on (READY).
    2. Drive the vehicle at 3 mph (5 km/h) or more for 30 seconds or more.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    None of the following DTCs are output.
    A
    Any of the following DTCs are output.
    B


    DTC No.
    Relevant Diagnosis
    P0A1A-155, 156, 166, 658, 791
    Generator Control Module
    P0A1B-163, 164, 192, 193, 198, 511, 512, 661, 786, 794
    Drive Motor "A" Control Module

  1. Turn the power switch off.



B
REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)
A


2.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Only DTC P0A1A-151, P0A1A-659 or P324E-788 is output.
    A
    Other than above.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A


3.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


4.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch off and wait for 30 seconds or more.

  1. Turn the power switch on (IG) and wait for 5 seconds or more.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    No DTCs are output (not including history DTCs).
    A
    Only DTC P0A1A-151, P0A1A-659 or P324E-788 is output.
    B
    Other than above.
    C

  1. Turn the power switch off.



B
REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER

C
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A

REPLACE MG CONTROL COMPUTER