Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P06B0-163    Sensor Power Supply "A" Circuit / Open

DTC    P06D6-511    Sensor Reference Voltage "F" Circuit / Open

DTC    P06E6-164    Sensor Power Supply "C" Circuit / Open

DTC    P0A1A-151    Generator Control Module

DTC    P0A1A-166    Generator Control Module

DTC    P0A1A-658    Generator Control Module

DTC    P0A1A-791    Generator Control Module

DTC    P0A1B-198    Drive Motor "A" Control Module

DTC    P0A1B-786    Drive Motor "A" Control Module

DTC    P0A1B-794    Drive Motor "A" Control Module

DTC    P1C2A-155    Generator A/D Converter Circuit

DTC    P1C2B-192    Drive Motor "A" A/D Converter Circuit

DTC    P1C73-512    Sensor Standard Voltage "F" Circuit / Open

DTC    P1CA6-156    Generator Control Module Malfunction

DTC    P1CA7-193    Drive Motor Control Module Malfunction

DTC    P3133-659    Communication Error from Generator to Drive Motor "A"

DTC    P3134-661    Communication Error from Drive Motor "A" to Generator

for Preparation Click here


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and it will set DTCs when it detects malfunctions.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P06B0
163
MG ECU internal malfunction
IPM positive power source error
(1 trip detection logic)
Inverter with converter assembly
P06D6
511
MG ECU internal malfunction
Standard voltage for analog signal offset (+2.5 V) error
(1 trip detection logic)
P06E6
164
MG ECU internal malfunction
IPM negative power source error
(1 trip detection logic)
P0A1A
151
MG ECU internal malfunction
Run pulse signal cycle deviation or stop
(1 trip detection logic)
P0A1A
166
MG ECU internal malfunction
R/D converter NM stop error
(1 trip detection logic)
P0A1A
658
MG ECU internal malfunction
Calculation check error
(1 trip detection logic)
P0A1A
791
MG ECU internal malfunction
R/D converter communication error
(1 trip detection logic)
P0A1B
198
MG ECU internal malfunction
R/D converter NM stop error
(1 trip detection logic)
P0A1B
786
MG ECU internal malfunction
Calculation check error
(1 trip detection logic)
P0A1B
794
MG ECU internal malfunction
R/D converter communication error
(1 trip detection logic)
P1C2A
155
MG ECU internal malfunction
A/D converter malfunction
(1 trip detection logic)
P1C2B
192
MG ECU internal malfunction
A/D converter malfunction
(1 trip detection logic)
P1C73
512
MG ECU internal malfunction
Standard voltage for analog signal (+5 V) error
(1 trip detection logic)
P1CA6
156
MG ECU internal malfunction
CPU ROM-RAM error
(1 trip detection logic)
P1CA7
193
MG ECU internal malfunction
CPU ROM-RAM error
(1 trip detection logic)
P3133
659
MG ECU internal malfunction
Communication error (from generator (MG1) to motor (MG2))
(1 trip detection logic)
P3134
661
MG ECU internal malfunction
Communication error (from motor (MG2) to generator (MG1))
(1 trip detection logic)

INSPECTION PROCEDURE

HINT:
  1. If DTC P06B0-163, P06D6-511, P06E6-164, P0A1A-151, P0A1A-658, P0A1A-791, P0A1B-786, P0A1B-794, P1C2A-155, P1C2B-192, P1C73-512, P3133-659 or P3134-661 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the power switch on (IG) and wait for 5 seconds or more.
  2. If DTC P1CA6-156 or P1CA7-193 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the power switch on (IG) and wait for 1 minute or more.
  3. If DTC P0A1A-166 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the power switch on (READY).
    2. With the vehicle stopped and the shift lever in P, depress the accelerator pedal and start the engine.
    3. Depress the accelerator pedal and keep the engine running for 30 seconds or more.
  4. If DTC P0A1B-198 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.
    1. Turn the power switch on (READY).
    2. Drive the vehicle at 5 km/h (3 mph) or more for 30 seconds or more.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    None of the following DTCs are output.
    A
    Any of the following DTCs are output.
    B


    DTC No.
    Relevant Diagnosis
    P06B0-163
    Sensor Power Supply "A" Circuit / Open
    P06D6-511
    Sensor Reference Voltage "F" Circuit / Open
    P06E6-164
    Sensor Power Supply "C" Circuit / Open
    P0A1A-166, 658, 791
    Generator Control Module
    P0A1B-198, 786, 794
    Drive Motor "A" Control Module
    P1C2A-155
    Generator A/D Converter Circuit
    P1C2B-192
    Drive Motor "A" A/D Converter Circuit
    P1C73-512
    Sensor Standard Voltage "F" Circuit / Open
    P1CA6-156
    Generator Control Module Malfunction
    P1CA7-193
    Drive Motor Control Module Malfunction
    P3134-661
    Communication Error from Drive Motor "A" to Generator

  1. Turn the power switch off.



B
REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)
A


2.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Only DTC P0A1A-151, P3133-659 or P324E-788 is output.
    A
    Other than above.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A


3.CLEAR DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read and record the DTCs and freeze frame data.

  1. Clear DTCs and freeze frame data.

  1. Turn the power switch off.


NEXT


4.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch off and wait for 30 seconds or more.

  1. Turn the power switch on (IG) and wait for 5 seconds or more.

  1. Turn the power switch on (READY).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    No DTCs are output (not including history DTCs).
    A
    Only DTC P0A1A-151, P3133-659 or P324E-788 is output.
    B
    Other than above.
    C

  1. Turn the power switch off.



B
REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER

C
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A

REPLACE MG CONTROL COMPUTER