Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0AFC-129    Hybrid Battery Pack Sensor Module

for Preparation Click here


DESCRIPTION

The battery smart unit (battery energy control module) sends HV battery voltage information to the power management control ECU via serial communication.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0AFC
129
HV battery voltage circuit malfunction
Battery smart unit

INSPECTION PROCEDURE

NOTICE:
  1. Performing the check procedures for a long time with the shift lever in N may cause DTC P3000-388 to be set.

    HINT:
    After performing troubleshooting, if it is necessary to replace the battery smart unit, voltages need to be confirmed after installing the new battery smart unit. Confirm that "Power Resource VB", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" in the Data List are 155 V or more with the power switch on (READY), shift lever in P, and the engine stopped. When the system is normal, the "Power Resource VB", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" values should be almost equal (voltage boosting will not occur when the shift lever is in N). If the difference between each voltage exceeds the values specified below, there must be a malfunction in the battery smart unit or the inverter with converter assembly.
    After performing troubleshooting, if it is necessary to replace the battery smart unit, voltages need to be confirmed after installing the new battery smart unit. Confirm that battery voltages (Power Resource VB), pre-boost voltage (VL), and post-boost voltage (VH) in the Data List are 220V or more with the power switch on (READY), shift lever in P, and the engine stopped. When the system is normal, the Power Resource VB, VL, and VH values should be almost equal (voltage boosting will not occur when the shift lever is in neutral). If the difference between each voltage exceeds the values specified below, there must be a malfunction in the battery smart unit or the inverter with converter assembly.

    Inspection voltage
    Maximum voltage difference
    Difference between "Power Resource VB" and "VL-Voltage before Boosting"
    35 V
    Difference between "Power Resource VB" and "VH-Voltage after Boosting"
    60 V
    Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting"
    80 V

  2. After the repair, if "VL-Voltage before Boosting" and "Power Resource VB" are approximately the same when the power switch is turned on (READY) with the shift lever in P and the accelerator pedal not depressed, the condition is judged as normal.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Only P0AFC-129 is output or P0AFC-129 and DTCs other than the ones in the table below are also output.
    A
    DTCs shown in Table 1 are output simultaneously.
    B
    DTCs shown in Table 2 are output simultaneously.
    C


    Table 1 
    DTC No.
    Relevant Diagnosis
    P0A1A-151, 155, 156, 658, 659
    Generator Control Module
    P0A1B-164, 193, 512, 661, 786
    Drive Motor "A" Control Module
    P0A1D-148
    Hybrid Powertrain Control Module
    P0A78-266, 267
    Drive Motor "A" Inverter Performance
    P0A94-589, 590
    DC/DC Converter Performance
    P2511-149
    ECM/PCM Power Relay Sensor Circuit Intermittent
    P3004-132
    High Voltage Power Resource
    P324E-788
    MG-ECU Power Relay Intermittent Circuit
    U0110 (all INF codes)*1
    Lost Communication with Drive Motor Control Module "A"

    Table 2 
    DTC No.
    Relevant Diagnosis
    P0AFC-123
    Hybrid Battery Pack Sensor Module
    P0B3D-123
    Hybrid Battery Voltage Sensor "A" Circuit Low
    P0B42-123
    Hybrid Battery Voltage Sensor "B" Circuit Low
    P0B47-123
    Hybrid Battery Voltage Sensor "C" Circuit Low
    P0B4C-123
    Hybrid Battery Voltage Sensor "D" Circuit Low
    P0B51-123
    Hybrid Battery Voltage Sensor "E" Circuit Low
    P0B56-123
    Hybrid Battery Voltage Sensor "F" Circuit Low
    P0B5B-123
    Hybrid Battery Voltage Sensor "G" Circuit Low
    P0B60-123
    Hybrid Battery Voltage Sensor "H" Circuit Low
    P0B65-123
    Hybrid Battery Voltage Sensor "I" Circuit Low
    P0B6A-123
    Hybrid Battery Voltage Sensor "J" Circuit Low
    P0B6F-123
    Hybrid Battery Voltage Sensor "K" Circuit Low
    P308A-123
    Hybrid Battery Voltage Sensor All Circuits Low

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P0AFC-129 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)

C
GO TO DTC CHART (HYBRID BATTERY SYSTEM) (Click here)
A

REPLACE BATTERY SMART UNIT (Click here)