Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0BEA-290    Drive Motor "A" Phase V Current Sensor Circuit Range / Performance

DTC    P0BEE-298    Drive Motor "A" Phase V Current Sensor Circuit Range / Performance

DTC    P1C3C-294    Drive Motor "A" Phase V Current Sensor Correlation

DTC    P1C3D-302    Drive Motor "A" Phase W Current Sensor Correlation

DTC    P1C4A-288    Drive Motor "A" Phase V Current Sensor Sub Circuit Range / Performance

DTC    P1C4F-296    Drive Motor "A" Phase W Current Sensor Sub Circuit Range / Performance

DTC    P1C6D-501    Drive Motor "A" Phase V Current Sensor Offset Range / Performance

DTC    P1C6E-502    Drive Motor "A" Phase W Current Sensor Offset Range / Performance

for Preparation Click here


DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors the motor inverter current sensors. P0A60 and P0A63 indicate malfunctions in current sensors, and they do not indicate malfunctions in the high-voltage system.

HINT:
The term "drive motor A" indicates MG2.


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0BEA
290
Malfunction in motor inverter current sensor (phase V main sensor)
(1 trip detection logic)
Inverter with converter assembly
P0BEE
298
Malfunction in motor inverter current sensor (phase W main sensor)
(1 trip detection logic)
P1C3C
294
Malfunction in motor inverter current sensor (performance problem or open phase V)
(1 trip detection logic)
P1C3D
302
Malfunction in motor inverter current sensor (performance problem or open phase W)
(1 trip detection logic)
P1C4A
288
Malfunction in motor inverter current sensor (phase V sub sensor)
(1 trip detection logic)
P1C4F
296
Malfunction in motor inverter current sensor (phase W sub sensor)
(1 trip detection logic)
P1C6D
501
Malfunction in motor inverter current sensor (phase V main and sub sensors offset)
(1 trip detection logic)
P1C6E
502
Malfunction in motor inverter current sensor (phase W main and sub sensors offset)
(1 trip detection logic)

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch on (IG) and wait for 5 seconds or more.
  2. Turn the power switch on (READY) with the shift lever in P and wait for 5 seconds or more.
  3. Move the shift lever to N and wait for 5 seconds or more.
  4. Depress the accelerator pedal of the vehicle with the engine stopped and the shift lever in P to start the engine.
  5. Drive the vehicle forward with the shift lever in D for 5 m or more.
  6. Drive the vehicle backward with the shift lever in R for 5 m or more.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    P0BEA-290, P0BEE-298, P1C3C-294, P1C3D-302, P1C4A-288, P1C4F-296, P1C6D-501 or P1C6E-502 only is output, or DTCs other than the ones in the table below are also output.
    A
    P0A78-202 is output.
    B

  1. Turn the power switch off.



B
GO TO DTC CHART (P0A78-202) (Click here)
A


2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



    A267460
  1. Check the connector connections and contact pressure of the low voltage connectors of the inverter with converter assembly (Click here).

    NOTICE:
    Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.

    OK:
    The connectors are connected securely and there are no contact pressure problems.

    HINT:
    When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.



NG
CONNECT SECURELY
OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)