Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0C76-523    Hybrid Battery System Discharge Time Too Long

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0D2F-266 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0C76
523
Inverter voltage (VH) sensor offset malfunction
  1. Inverter with converter assembly
  2. Wire harness or connector
  3. Hybrid vehicle control ECU

HINT:
When the power switch is turned off, the MG ECU applies current to MG2 in a way that does not generate torque, in order to discharge the residual voltage in the inverter. When the hybrid system is normal, the VH value is almost 0 V after discharge. This DTC will be stored if the VH value is more than the specified value after discharge.


A111758E02


WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225 .
Refer to the wiring diagram for DTC P321E-318 .

INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Turn the power switch off and wait for 30 seconds or more.
  2. Turn the power switch on (READY) and wait for 30 seconds or more.
  3. Turn the power switch off and wait for 30 seconds or more.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Only P0C76-523 is output or P0C76-523 and DTCs other than the ones in the table below are also output.
    A
    Any of the following DTCs are also output.
    B


    DTC No.
    Relevant Diagnosis
    P06B0-163
    Sensor Power Supply "A" Circuit/Open
    P06D6-511
    Sensor Reference Voltage "F" Circuit/Open
    P06E6-164
    Sensor Power Supply "C" Circuit/Open
    P0A1A-151, 658, 791
    Generator Control Module
    P0A1B-786, 794
    Drive Motor "A" Control Module
    P0A1D-148
    Hybrid Powertrain Control Module
    P0A3F-243
    Drive Motor "A" Position Sensor Circuit
    P0A40-500
    Drive Motor "A" Position Sensor Circuit Range/Performance
    P0A41-245
    Drive Motor "A" Position Sensor Circuit Low
    P0A4B-253
    Generator Position Sensor Circuit
    P0A4C-513
    Generator Position Sensor Circuit Range/Performance
    P0A4D-255
    Generator Position Sensor Circuit Low
    P0ADC-226
    Hybrid Battery Positive Contactor Control Circuit High
    P0AE0-228
    Hybrid Battery Negative Contactor Control Circuit High
    P0AE7-224
    Hybrid Battery Precharge Contactor Control Circuit High
    P0D2F-266
    Drive Motor "A" Inverter Voltage Sensor Circuit Low
    P0D30-267
    Drive Motor "A" Inverter Performance
    P1C2A-155
    Generator A/D Converter Circuit
    P1CA6-156
    Generator Control Module Malfunction
    P1CA7-193
    Drive Motor Control Module Malfunction
    P1CAC-200
    Generator Position Sensor Angle Malfunction
    P1CAD-168
    Drive Motor "A" Position Sensor Angle Malfunction
    P1CAF-792
    Generator Position Sensor REF Signal Cycle Malfunction
    P1CB0-795
    Drive Motor "A" Position Sensor REF Signal Cycle Malfunction
    P1CB2-793
    Generator Position Sensor REF Signal Stop Malfunction
    P1CB3-796
    Drive Motor "A" Position Sensor REF Signal Stop Malfunction
    P2511-149
    HV CPU Power Relay Sense Circuit Intermittent No Continuity
    P3133-659
    Communication Error from Generator to Drive Motor "A"
    P3134-661
    Communication Error from Drive Motor "A" to Generator
    P324E-788
    MG-ECU Power Relay Intermittent Circuit
    U0110 (all INF codes)*1
    Lost Communication with Drive Motor Control Module "A"

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P0C76-523 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)
A


2.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Any of the following DTCs are also output.
    A
    Only P0C76-523 is output or P0C76-523 and DTCs other than the ones in the table below are also output.
    B


    DTC No.
    Relevant Diagnosis
    P0A90-251, 509
    Drive Motor "A" Performance
    P0A92-261, 521
    Hybrid Generator Performance
    P0C19-306
    Drive Motor "A" Torque Delivered Performance
    P0E71-344
    Generator Torque Delivered Performance

    HINT:
    When the DTCs listed in the table above are also output, there may be a short between the HSDN (MG shut down signal) circuit and power circuit.

  1. Turn the power switch off.



B
REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)
A


3.CHECK HYBRID VEHICLE CONTROL ECU
  1. Turn the power switch on (IG).



    A252924E55
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-12 (HSDN) - G80-6 (E1)
    Power switch on (IG)
    Below 4.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (Hybrid Vehicle Control ECU)

  1. Turn the power switch off.



NG
Go to step 4
OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)  

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A47 from the inverter with converter assembly.

  1. Disconnect connector A72 from the hybrid vehicle control ECU.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).



    A216755E38
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A47-31 (HSDN) or A72-12 (HSDN) - Body ground
    Power switch on (IG)
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Inverter with Converter Assembly)
    *b
    Rear view of wire harness connector
    (to Hybrid Vehicle Control ECU)

    NOTICE:
    Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A72-12 (HSDN) - A72-4 (+B1)
    Power switch off
    10 kΩ or higher
    A72-12 (HSDN) - A72-6 (MREL)
    Power switch off
    10 kΩ or higher
    A47-31 (HSDN) - A47-10 (+B)
    Power switch off
    10 kΩ or higher
    A47-31 (HSDN) - A47-9 (+B2)
    Power switch off
    10 kΩ or higher

  1. Connect the inverter with converter assembly connector.

  1. Connect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK INVERTER WITH CONVERTER ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Disconnect connector A47 from the inverter with converter assembly.



    A215652E44
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A47-31 (HSDN) - A47-10 (+B)
    Power switch off
    5 kΩ or higher
    A47-31 (HSDN) - A47-9 (+B2)
    Power switch off
    5 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Inverter with Converter Assembly)

  1. Connect the inverter with converter assembly connector.



NG
REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)
OK

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)