Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM

DTC    P0A94-585    DC / DC Converter Performance

for Preparation Click here


DESCRIPTION

Refer to the description for DTC P0A94-589 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A94
585
Boost converter voltage (VL) sensor performance problem
Inverter with converter assembly

INSPECTION PROCEDURE

HINT:
When the accelerator pedal is not depressed with the power switch on (READY) and the shift lever in P, if "VL-Voltage before Boosting" and the "Power Resource VB" is approximately same after repair, the condition is judged as normal.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.

    Result:
    Result
    Proceed to
    Only P0A94-585 is output or P0A94-585 and DTCs other than the ones in the table below are also output.
    A
    DTCs shown in Table 1 are output simultaneously.
    B
    DTCs shown in Table 2 are output simultaneously.
    C


    Table 1 
    DTC No.
    Relevant Diagnosis
    P0A1A-151, 155, 156, 658, 659
    Generator Control Module
    P0A1B-164, 193, 512, 661, 786
    Drive Motor "A" Control Module
    P0A1D-148
    Hybrid Powertrain Control Module
    P0A78-266, 267
    Drive Motor "A" Inverter Performance
    P0A94-589, 590
    DC/DC Converter Performance
    P2511-149
    ECM/PCM Power Relay Sensor Circuit Intermittent
    P3004-132
    High Voltage Power Resource
    P324E-788
    MG-ECU Power Relay Intermittent Circuit
    U0110 (all INF codes)*1
    Lost Communication with Drive Motor Control Module "A"

    Table 2 
    DTC No.
    Relevant Diagnosis
    P0AFC-123
    Hybrid Battery Pack Sensor Module
    P0B3D-123
    Hybrid Battery Voltage Sensor "A" Circuit Low
    P0B42-123
    Hybrid Battery Voltage Sensor "B" Circuit Low
    P0B47-123
    Hybrid Battery Voltage Sensor "C" Circuit Low
    P0B4C-123
    Hybrid Battery Voltage Sensor "D" Circuit Low
    P0B51-123
    Hybrid Battery Voltage Sensor "E" Circuit Low
    P0B56-123
    Hybrid Battery Voltage Sensor "F" Circuit Low
    P0B5B-123
    Hybrid Battery Voltage Sensor "G" Circuit Low
    P0B60-123
    Hybrid Battery Voltage Sensor "H" Circuit Low
    P0B65-123
    Hybrid Battery Voltage Sensor "I" Circuit Low
    P0B6A-123
    Hybrid Battery Voltage Sensor "J" Circuit Low
    P0B6F-123
    Hybrid Battery Voltage Sensor "K" Circuit Low
    P308A-123
    Hybrid Battery Voltage Sensor All Circuits Low

    HINT:
    1. *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
    2. P0A94-585 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.

  1. Turn the power switch off.



B
GO TO DTC CHART (HYBRID CONTROL SYSTEM) (Click here)

C
GO TO DTC CHART (HYBRID BATTERY SYSTEM) (Click here)
A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS (Click here)