DTC P1C2D-587 Hybrid Battery Voltage / DC/DC Converter Voltage Correlation |

| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P1C2D | 587 | Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate |
|
| 1.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Check if DTCs are output.
| Result | Proceed to |
| DTC P1C2D-587 only is output. Alternatively, P1C2D-587 and any DTCs other than P0B23-129, P0CA3-442 or P0E32-585 are output. | A |
| P1C2D-587 and P0B23-129 (HV battery voltage circuit malfunction) are output. | B |
| P1C2D-587 and P0CA3-442 (abnormal voltage execution value) are output. | C |
| P1C2D-587 and P0E32-585 (boost converter voltage (VL) sensor performance problem) are output. | D |
Turn the power switch off.
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read and record the DTCs and freeze frame data.
Clear DTCs and freeze frame data.
Turn the power switch off.
| NEXT | |
| 3.CHECK DTC OUTPUT (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3. (*1)
Turn the power switch on (READY). (*2)
Enter the following menus: Powertrain / Hybrid Control / Data List (*3)
If both "Power Resource VB" and "VL-Voltage before Boosting" are less than 155 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 155 V or more. (*4)
Move the shift lever to P. (*5)
Set the air conditioning to MAX COOL and turn the headlights on. (*6)
Confirm that "Batt Pack Current Val" is more than 3 A. (*7)
Leave the vehicle for 15 seconds with the engine stopped during steps (*5) (*6) and (*7). (*8)
Enter the following menus: Powertrain / Hybrid Control / DTC. (*9)
Check if DTCs are output. (*10)
| Result | Proceed to |
| No DTCs are output, or DTCs other than the following are output. | A |
| P0B23-129 (Hybrid Battery "A" Voltage) is output. | B |
| P0E32-585 (DC/DC Converter Voltage Sensor "A" Range / Performance) is output. | C |
| P3000-388 (discharge inhibition) is output. | D |
| P3004-132 (high voltage power supply line problem) is output. | E |
Turn the power switch off.
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 4.CHECK DTC OUTPUT (HYBRID CONTROL) |
Turn the power switch on (READY). (*11)
Perform a road test that repeats full acceleration to 60 km/h (37 mph) and then braking to a complete stop three times. (*12)
Connect the intelligent tester to the DLC3. (*13)
Enter the following menus: Powertrain / Hybrid Control / DTC. (*14)
Check if DTCs are output. (*15)
| Result | Proceed to |
| No DTCs are output, or DTCs other than the following are output. | A |
| P0B23-129 (Hybrid Battery "A" Voltage) is output. | B |
| P0E32-585 (DC/DC Converter Voltage Sensor "A" Range / Performance) is output. | C |
| P3000-388 (discharge inhibition) is output. | D |
| P3004-132 (high voltage power supply line problem) is output. | E |
Turn the power switch off.
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 5.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Data List.
Select "Power Resource VB", "VL-Voltage before Boosting" and "VH-Voltage after Boosting" in the Data List.
If both "Power Resource VB" and VL-Voltage before Boosting are less than 155 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 155 V or more.
Move the shift lever to P (the engine is off), and read the Data List when the vehicle is stationary.
| Result | Proceed to |
| Both of the following are not satisfied. | A |
Both of the following are satisfied:
| B |
Both of the following are satisfied:
| C |
Turn the power switch off.
|
| ||||
|
| ||||
| A | |
| 6.CHECK FREEZE FRAME DATA (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read the freeze frame data of DTC P1C2D-587.
| Result | Proceed to |
| Both of the following are satisfied or both of the following are not satisfied. | A |
| "Power Resource VB" is less than 114 V or more than 200 V. | B |
| "VL-Voltage before Boosting" is less than 114 V or more than 200 V. | C |
Turn the power switch off.
|
| ||||
|
| ||||
| A | |
| 7.CHECK FREEZE FRAME DATA (HYBRID CONTROL) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read the freeze frame data of DTC P1C2D-587.
| Result | Proceed to |
| Others (Freeze frame data is not stored). | A |
Both of the following are satisfied:
| B |
| Neither A nor B is satisfied. | C |
Turn the power switch off.
|
| ||||
|
| ||||
| A | |
| 8.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Data List.
If both "Battery Block Vol" and "VL-Voltage before Boosting" are less than 155 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 155 V or more.
Move the shift lever to P (the engine is off), and read the "Power Resource VB" and all of the "Battery Block Vol", when the vehicle is stationary.
| Result | Proceed to |
Both of the following are satisfied:
| A |
| The preceding condition is not satisfied. | B |
Turn the power switch off.
|
| ||||
| A | ||
| ||