Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

DTC    C2177/77    Initialization not Completed

for Preparation Click here


DESCRIPTION

Initialization is necessary if one of the following occurs:
  1. The tire pressure warning ECU and receiver is replaced.
  2. A tire pressure warning valve and transmitter is replaced.
  3. Tires with different standard tire pressures are installed.
  4. The tires are rotated.
  5. A new vehicle is delivered.

DTC No.
DTC Detection Condition
Trouble Area
C2177/77
  1. All conditions below are met:
  1. During initialization
  2. Tire pressure warning valve and transmitter is not in stop mode
  3. Signal is not received from tire pressure warning valve and transmitter for 20 minutes or more
  4. Vehicle speed is more than 40 km/h (25 mph) for 20 minutes or more
  1. Tire pressure warning valve and transmitter
  2. Wire harness or connector
  3. Tire pressure warning ECU and receiver

WIRING DIAGRAM


C277675E04


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.

1.CHECK FREQUENCY RECEIVING CONDITION
  1. Check that the vehicle is not located in an area such as described below:

    1. Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.

      HINT:
      If the vehicle is located in an area such as the one described above, the tire pressure warning light may illuminate after blinking 1 minute due to interfering radio frequencies.

    2. Devices using similar radio frequencies are used in the vehicle.

      OK:
      Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.

      HINT:
      Radio transmissions may be interrupted due to the surroundings, or devices installed by the user.



NG
CHECK IF ANY DEVICE IS INSTALLED BY USER
OK


2.PERFORM INITIALIZATION
  1. Perform initialization (Click here).


NEXT


3.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the power switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1

    HINT:
    1. *1: It may take a few minutes until the values are displayed.
    2. When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.


    Result:

    Result
    Proceed to
    All tire pressure readings are equal to specified values.
    A
    Tire pressure values are not displayed.
    B



B
GO TO DTC C2121/21 TO C2124/24 (Click here)
A

END