POWER WINDOW CONTROL SYSTEM > Driver Side Power Window does not Operate with Power Window Master Switch |

| 1.READ VALUE USING INTELLIGENT TESTER (MAIN BODY) |
Connect the intelligent tester to the DLC3.
Turn the power switch to on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Communication D-Door Motor | Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP | OK: Normal communication STOP: Communication stopped | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR) |
Enter the following menus: Body / D-Door Motor / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| D Door P/W Up SW | Driver door power window manual up switch signal / ON or OFF | ON: Driver door power window manual up switch operated OFF: Driver door power window manual up switch not operated | - |
| D Door P/W Down SW | Driver door power window manual down switch signal / ON or OFF | ON: Driver door power window manual down switch operated OFF: Driver door power window manual down switch not operated | - |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DRIVER DOOR WINDOW MOTOR) |
Enter the following menus: Body / D-Door Motor / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power Window | Power window | OFF / UP / DOWN | - |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND) |
Disconnect the power window regulator motor assembly (for driver door) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J3-2 (B) - Body ground | Power switch off | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| H3-2 (B) - Body ground | Power switch off | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| J3-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| H3-1 (GND) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND) |
Disconnect the power window regulator master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J1-8 (U) - J3-10 (UP) | Always | Below 1 Ω |
| J1-5 (D) - J3-7 (DOWN) | Always | Below 1 Ω |
| J1-8 (U) - Body ground | Always | 10 kΩ or higher |
| J1-5 (D) - Body ground | Always | 10 kΩ or higher |
| J1-1 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| H1-1 (U) - H3-10 (UP) | Always | Below 1 Ω |
| H1-5 (D) -H3-7 (DOWN) | Always | Below 1 Ω |
| H1-1 (U) - Body ground | Always | 10 kΩ or higher |
| H1-5 (D) - Body ground | Always | 10 kΩ or higher |
| H1-9 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
![]() |
Remove the power window regulator master switch assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 8 (U) - 1 (E) | Manual UP | Below 1 Ω |
| 5 (D) - 1 (E) | Manual DOWN | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
| 1 (U) - 9 (E) | Manual UP | Below 1 Ω |
| 5 (D) - 9 (E) | Manual DOWN | Below 1 Ω |
| *A | for LHD |
| *B | for RHD |
| *a | Component without harness connected (Power Window Regulator Master Switch Assembly) |
|
| ||||
| OK | ||
| ||