AUDIO AND VISUAL SYSTEM > Steering Pad Switch Circuit |

| 1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL) |
Disconnect the radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G41-21 (SW1) - Body ground | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 323 to 335 Ω | |
| Volume+ switch pushed | 980 to 1020 Ω | |
| Volume- switch pushed | 3048 to 3172 Ω | |
| G41-22 (SW2) - Body ground | No switch pushed | 95 to 105 kΩ |
| MODE switch pushed | Below 2.5 Ω |
|
| ||||
| OK | ||
| ||
| 2.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z2-10 (AU1) - z2-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 323 to 335 Ω | |
| Volume+ switch pushed | 980 to 1020 Ω | |
| Volume- switch pushed | 3048 to 3172 Ω | |
| z2-9 (AU2) - z2-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE switch pushed | Below 2.5 Ω |
| *a | Component without harness connected (Steering Pad Switch Assembly) | *b | Seek+ |
| *c | Seek- | *d | Volume+ |
| *e | Volume- | *f | MODE |
Proceed to the next step based on the inspection result.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.INSPECT STEERING PAD SWITCH RH |
Disconnect the steering pad switch RH connectors.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| SR1-3 (AU1) - z2-10 (AU1) | Always | Below 1 Ω |
| SR1-4 (AU2) - z2-9 (AU2) | Always | Below 1 Ω |
| SR1-5 (EAU) - z2-8 (EAU) | Always | Below 1 Ω |
| *a | Component without harness connected (Steering Pad Switch RH) | - | - |
|
| ||||
| OK | ||
| ||
| 4.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY |
Disconnect the steering pad switch assembly connector.
Disconnect the spiral cable with sensor sub-assembly connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z2-8 (EAU) - G5-4 (EAU) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z2-10 (AU1) - G5-6 (AU1) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z2-9 (AU2) - G5-5 (AU2) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.
| Tester Connection | Condition | Specified Condition |
| z2-8 (EAU) - G5-4 (EAU) | Always | Below 3 Ω |
| z2-10 (AU1) - G5-6 (AU1) | Always | Below 3 Ω |
| z2-9 (AU2) - G5-5 (AU2) | Always | Below 3 Ω |
| *a | Component without harness connected (Spiral Cable with Sensor Sub-assembly) |
| *b | Steering Pad Switch Assembly Side |
| *c | Vehicle Side |
|
| ||||
| OK | ||
| ||