POWER WINDOW CONTROL SYSTEM > TERMINALS OF ECU |
| POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |

| *A | for LHD | *B | for RHD |
Disconnect the J1*1, H1*2 power window regulator master switch assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J1-1 (E) - Body ground | LA - Body ground | Ground | Always | Below 1 Ω |
| J1-6 (B) - J1-1 (E) | LA-GR - LA | Power supply | Power switch on (IG) | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| H1-9 (E) - Body ground | LA - Body ground | Ground | Always | Below 1 Ω |
| H1-6 (B) - H1-9 (E) | LA-GR - LA | Power supply | Power switch on (IG) | 11 to 14 V |
Reconnect the J1*1, H1*2 power window regulator master switch assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J1-8 (U) - J1-1 (E) | R - LA | Power window motor UP output | Power switch on (IG), driver door power window switch OFF → UP (Manual operation) | 11 to 14 V → Below 1 V |
| J1-4 (AUTO) - J1-1 (E) | R - LA | Power window motor AUTO UP output | Power switch on (IG), driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed | 11 to 14 V → Below 1 V → 11 to 14 V |
| Power window motor AUTO DOWN output | Power switch on (IG), driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open | 11 to 14 V → Below 1 V → 11 to 14 V | ||
| J1-5 (D) - J1-1 (E) | G - LA | Power window motor DOWN output | Power switch on (IG), driver door power window switch OFF → DOWN (Manual operation) | 11 to 14 V → Below 1 V |
| J1-16 (U) - J1-1 (E) | LA-W - LA | Power window motor UP output | Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| J1-15 (D) - J1-1 (E) | LA-P - LA | Power window motor DOWN output | Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| J1-12 (U) - J1-1 (E) | LA-Y - LA | Power window motor UP output | Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| J1-13 (D) - J1-1 (E) | LA-B - LA | Power window motor DOWN output | Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| J1-10 (U) - J1-1 (E) | LA-R - LA | Power window motor UP output | Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| J1-18 (D) - J1-1 (E) | LA-G - LA | Power window motor DOWN output | Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| H1-1 (U) - H1-9 (E) | G - LA | Power window motor UP output | Power switch on (IG), driver door power window switch OFF → UP (Manual operation) | 11 to 14 V → Below 1 V |
| H1-4 (AUTO) - H1-9 (E) | R - LA | Power window motor AUTO UP output | Power switch on (IG), driver door power window fully open → driver door power window switch UP (AUTO UP position) → driver door power window fully closed | 11 to 14 V → Below 1 V → 11 to 14 V |
| Power window motor AUTO DOWN output | Power switch on (IG), driver door power window fully closed → driver door power window switch DOWN (AUTO DOWN position) → driver door power window fully open | 11 to 14 V → Below 1 V → 11 to 14 V | ||
| H1-5 (D) - H1-9 (E) | R - LA | Power window motor DOWN output | Power switch on (IG), driver door power window switch OFF → DOWN (Manual operation) | 11 to 14 V → Below 1 V |
| H1-12 (U) - H1-9 (E) | LA-W - LA | Power window motor UP output | Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| H1-13 (D) - H1-9 (E) | LA-P - LA | Power window motor DOWN output | Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| H1-18 (U) - H1-9 (E) | LA-Y - LA | Power window motor UP output | Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| H1-10 (D) - H1-9 (E) | LA-B - LA | Power window motor DOWN output | Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| H1-16 (U) - H1-9 (E) | LA-R - LA | Power window motor UP output | Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| H1-15 (D) - H1-9 (E) | LA-G - LA | Power window motor DOWN output | Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Door) |

| *A | for LHD | *B | for RHD |
Disconnect the H2*1,J2*2 power window regulator switch assembly (for front passenger door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| H2-3 (B) - Body ground | LA-L - Body ground | Power supply | Power switch on (IG) | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J2-3 (B) - Body ground | LA-L - Body ground | Power supply | Power switch on (IG) | 11 to 14 V |
Reconnect the H2*1,J2*2 power window regulator switch assembly (for front passenger door).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| H2-4 (U) - Body ground | LA-R - Body ground | Power window motor UP output | Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| H2-1 (D) - Body ground | LA-G - Body ground | Power window motor DOWN output | Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J2-4 (U) - Body ground | LA-R - Body ground | Power window motor UP output | Power switch on (IG), front passenger door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| J2-1 (D) - Body ground | LA-G - Body ground | Power window motor DOWN output | Power switch on (IG), front passenger door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear LH Door) |

Disconnect the L1 power window regulator switch assembly (for rear LH door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L1-3 (B) - Body ground | LA-SB - Body ground | Power supply | Power switch on (IG) | 11 to 14 V |
Reconnect the L1 power window regulator switch assembly (for rear LH door).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| L1-4 (U) - Body ground | LA-Y - Body ground | Power window motor UP output | Power switch on (IG), rear LH door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| L1-1 (D) - Body ground | LA-B - Body ground | Power window motor DOWN output | Power switch on (IG), rear LH door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Rear RH Door) |

Disconnect the K1 power window regulator switch assembly (for rear RH door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K1-3 (B) - Body ground | LA-SB - Body ground | Power supply | Power switch on (IG) | 11 to 14 V |
Reconnect the K1 power window regulator switch assembly (for rear RH door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| K1-4 (U) - Body ground | LA-Y - Body ground | Power window motor UP output | Power switch on (IG), rear RH door power window switch OFF → UP (Manual operation) | Below 1 V → 11 to 14 V |
| K1-1 (D) - Body ground | LA-B - Body ground | Power window motor DOWN output | Power switch on (IG), rear RH door power window switch OFF → DOWN (Manual operation) | Below 1 V → 11 to 14 V |
| CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) |

| *A | for LHD | *B | for RHD |
Disconnect the J3*1, H3*2 power window regulator motor assembly (for driver door) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J3-1 (GND) - Body ground | LA - Body ground | Ground | Always | Below 1 Ω |
| J3-2 (B) - Body ground | LA-G - Body ground | Power supply | Power switch off | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| H3-1 (GND) - Body ground | LA - Body ground | Ground | Always | Below 1 Ω |
| H3-2 (B) - Body ground | LA-LG - Body ground | Power supply | Power switch off | 11 to 14 V |
Reconnect the J3*1, H3*2 power window regulator motor assembly (for driver door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| J3-4 (AUTO) - J3-1 (GND) | R - LA | Power window motor AUTO UP input | Power switch on (IG), driver door power window fully open | 11 to 14 V |
| J3-4 (AUTO) - J3-1 (GND) | R - LA | Power window motor AUTO UP input | Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| J3-4 (AUTO) - J3-1 (GND) | R - LA | Power window motor AUTO UP input | Power switch on (IG), driver door power window fully closed | 11 to 14 V |
| J3-4 (AUTO) - J3-1 (GND) | R - LA | Power window motor AUTO DOWN input | Power switch on (IG), driver door power window fully closed | 11 to 14 V |
| J3-4 (AUTO) - J3-1 (GND) | R - LA | Power window motor AUTO DOWN input | Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| J3-4 (AUTO) - J3-1 (GND) | R - LA | Power window motor AUTO DOWN input | Power switch on (IG), driver door power window fully open | 11 to 14 V |
| J3-5 (LED) - J3-1 (GND) | W - LA | LED illumination signal | Power switch on (IG) | 11 to 14 V |
| J3-5 (LED) - J3-1 (GND) | W - LA | LED illumination signal | Approximately 43 seconds after power switch turned off | Below 1 V |
| J3-7 (DOWN) - J3-1 (GND) | G - LA | Power window motor DOWN input | Power switch on (IG), driver door power window regulator switch not pushed or pulled | 11 to 14 V |
| J3-7 (DOWN) - J3-1 (GND) | G - LA | Power window motor DOWN input | Power switch on (IG), driver door power window regulator switch pushed halfway down (Manual operation) | Below 1 V |
| J3-7 (DOWN) - J3-1 (GND) | G - LA | Power window motor DOWN input | Power switch on (IG), driver door power window fully closed | 11 to 14 V |
| J3-7 (DOWN) - J3-1 (GND) | G - LA | Power window motor DOWN input | Power switch on (IG), driver door power window regulator switch fully pushed down (Automatic position) | Below 1 V |
| J3-7 (DOWN) - J3-1 (GND) | G - LA | Power window motor DOWN input | Power switch on (IG), driver door power window fully open | 11 to 14 V |
| J3-10 (UP) - J3-1 (GND) | R - LA | Power window motor UP input | Power switch on (IG), driver door power window regulator switch not pushed or pulled | 11 to 14 V |
| J3-10 (UP) - J3-1 (GND) | R - LA | Power window motor UP input | Power switch on (IG), driver door power window regulator switch pulled halfway up (Manual operation) | Below 1 V |
| J3-10 (UP) - J3-1 (GND) | R - LA | Power window motor UP input | Power switch on (IG), driver door power window fully open | 11 to 14 V |
| J3-10 (UP) - J3-1 (GND) | R - LA | Power window motor UP input | Power switch on (IG), driver door power window regulator switch fully pulled up (Automatic operation) | Below 1 V |
| J3-10 (UP) - J3-1 (GND) | R - LA | Power window motor UP input | Power switch on (IG), driver door power window fully closed | 11 to 14 V |
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| H3-4 (AUTO) - H3-1 (GND) | R - LA | Power window motor AUTO UP input | Power switch on (IG), driver door power window fully open | 11 to 14 V |
| H3-4 (AUTO) - H3-1 (GND) | R - LA | Power window motor AUTO UP input | Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pulled up (Automatic operation) | Below 1 V |
| H3-4 (AUTO) - H3-1 (GND) | R - LA | Power window motor AUTO UP input | Power switch on (IG), driver door power window fully closed | 11 to 14 V |
| H3-4 (AUTO) - H3-1 (GND) | R - LA | Power window motor AUTO DOWN input | Power switch on (IG), driver door power window fully closed | 11 to 14 V |
| H3-4 (AUTO) - H3-1 (GND) | R - LA | Power window motor AUTO DOWN input | Power switch on (IG), driver door power window moving, power window regulator switch assembly fully pushed down (Automatic operation) | Below 1 V |
| H3-4 (AUTO) - H3-1 (GND) | R - LA | Power window motor AUTO DOWN input | Power switch on (IG), driver door power window fully open | 11 to 14 V |
| H3-5 (LED) - H3-1 (GND) | W - LA | LED illumination signal | Power switch on (IG) | 11 to 14 V |
| H3-5 (LED) - H3-1 (GND) | W - LA | LED illumination signal | Approximately 43 seconds after power switch turned off | Below 1 V |
| H3-7 (DOWN) - H3-1 (GND) | R - LA | Power window motor DOWN input | Power switch on (IG), driver door power window regulator switch not pushed or pulled | 11 to 14 V |
| H3-7 (DOWN) - H3-1 (GND) | R - LA | Power window motor DOWN input | Power switch on (IG), driver door power window regulator switch pushed halfway down (Manual operation) | Below 1 V |
| H3-7 (DOWN) - H3-1 (GND) | R - LA | Power window motor DOWN input | Power switch on (IG), driver door power window fully closed | 11 to 14 V |
| H3-7 (DOWN) - H3-1 (GND) | R - LA | Power window motor DOWN input | Power switch on (IG), driver door power window regulator switch fully pushed down (Automatic position) | Below 1 V |
| H3-7 (DOWN) - H3-1 (GND) | R - LA | Power window motor DOWN input | Power switch on (IG), driver door power window fully open | 11 to 14 V |
| H3-10 (UP) - H3-1 (GND) | G - LA | Power window motor UP input | Power switch on (IG), driver door power window regulator switch not pushed or pulled | 11 to 14 V |
| H3-10 (UP) - H3-1 (GND) | G - LA | Power window motor UP input | Power switch on (IG), driver door power window regulator switch pulled halfway up (Manual operation) | Below 1 V |
| H3-10 (UP) - H3-1 (GND) | G - LA | Power window motor UP input | Power switch on (IG), driver door power window fully open | 11 to 14 V |
| H3-10 (UP) - H3-1 (GND) | G - LA | Power window motor UP input | Power switch on (IG), driver door power window regulator switch fully pulled up (Automatic operation) | Below 1 V |
| H3-10 (UP) - H3-1 (GND) | G - LA | Power window motor UP input | Power switch on (IG), driver door power window fully closed | 11 to 14 V |
| CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
Disconnect the MB main body ECU (multiplex network body ECU) connector.

| *A | Main body ECU (multiplex network body ECU) with 1 connector | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |

| *A | Main body ECU (multiplex network body ECU) with 2 connectors | - | - |
| *1 | Main body ECU (multiplex network body ECU) | - | - |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-30 (BECU) - Body ground | - | Auxiliary battery power supply | Power switch off | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Power switch on (ACC) | 11 to 14 V |
| MB-29 (ACC) - Body ground | - | ACC power supply | Power switch off | Below 1 V |
| MB-32 (IG) - Body ground | - | Power switch power supply | Power switch on (IG) | 11 to 14 V |
| MB-32 (IG) - Body ground | - | Power switch power supply | Power switch off | Below 1 V |
Reconnect the MB main body ECU (multiplex network body ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| G59-2 (KOFF) - Body ground | L - Body ground | Power window relay operation signal | Power switch on (IG) | 11 to 14 V |
| G59-2 (KOFF) - Body ground | L - Body ground | Power window relay operation signal | Approximately 43 seconds after power switch turned off | Below 1 V |
| 3D-36 (FLCY) - Body ground | R - Body ground | Front door courtesy switch LH input | Front door LH open | Below 1 V |
| 3D-36 (FLCY) - Body ground | R - Body ground | Front door courtesy switch LH input | Front door LH closed | Pulse generation |
| G59-19 (FRCY) - Body ground | R - Body ground | Front door courtesy switch RH input | Front door RH open | Below 1 V |
| G59-19 (FRCY) - Body ground | R - Body ground | Front door courtesy switch RH input | Front door RH closed | Pulse generation |