Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK COMBINATION METER ASSEMBLY


  1. Disconnect the G1 combination meter assembly connector.


    E238019E04

  2. Measure the resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G1-20 (ET) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    G1-12 (SW) - Body ground
    BE - Body ground
    Front passenger seat belt buckle switch signal
    Power switch on (IG), front passenger seat occupied, front passenger seat belt fastened
    10 kΩ or higher
    G1-12 (SW) - Body ground
    BE - Body ground
    Front passenger seat belt buckle switch signal
    Power switch on (IG), front passenger seat occupied, front passenger seat belt unfastened
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the G1 combination meter assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G1-21 (IG+) - Body ground
    B - Body ground
    Ignition power supply
    (IG signal)
    Power switch off
    Below 1 V
    G1-21 (IG+) - Body ground
    B - Body ground
    Ignition power supply
    (IG signal)
    Power switch on (IG)
    11 to 14 V
    If the result is not as specified, the combination meter assembly may have a malfunction.


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


  1. Disconnect the MB main body ECU (multiplex network body ECU) connector.


    B281049E03


    Text in Illustration 
    *A
    Main body ECU (multiplex network body ECU) with 1 connector
    *B
    for LHD
    *C
    for RHD
    -
    -
    *1
    Main body ECU (multiplex network body ECU)
    -
    -

    B297238E01


    Text in Illustration 
    *A
    Main body ECU (multiplex network body ECU) with 2 connectors
    -
    -
    *1
    Main body ECU (multiplex network body ECU)
    -
    -

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Power switch off
    Below 1 V
    MB-32 (IG) - Body ground
    -
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    Power switch power supply
    Power switch off
    Below 1 V
    MB-18 (DBKL) - Body ground
    -
    Driver seat belt buckle switch signal
    Driver seat belt fastened
    10 kΩ or higher
    MB-18 (DBKL) - Body ground
    -
    Driver seat belt buckle switch signal
    Driver seat belt unfastened
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.