Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT COMBINATION METER ASSEMBLY
  1. Check speedometer operation.

    NOTICE:
    1. The combination meter assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.
    2. The Data List values of the skid control ECU are used for this inspection. Therefore, make sure to perform the inspection after confirming that no DTCs are output from the brake control system.
    3. If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform the inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.


    1. Before starting the following inspection, check if brake control system DTCs are output.

    2. Check the values by referring to the table below.

      ABS/VSC/TRC:

      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Vehicle Speed
      Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations


      Reference: (km/h) except Australia 
      Intelligent tester indication (km/h)
      Acceptable Range (km/h)
      20
      21.0 to 25.0
      40
      42.0 to 46.0
      60
      63.0 to 67.0
      80
      84.0 to 88.0
      100
      104.0 to 109.0
      120
      125.0 to 130.0
      140
      146.0 to 151.0
      160
      167.0 to 173.0
      180
      187.0 to 194.0
      200
      208.0 to 215.0
      220
      229.0 to 236.0
      240
      249.0 to 257.0
      260
      270.0 to 278.0

      Reference: (km/h) for Australia 
      Intelligent tester indication (km/h)
      Acceptable Range (km/h)
      Data in ( ) is for reference
      20
      20.3 to 24.3
      40
      40.5 to 45.0
      60
      60.8 to 65.3
      80
      81.1 to 86.1
      100
      101.3 to 105.3
      120
      121.6 to 126.6
      140
      141.9 to 146.9
      160
      162.1 to 167.1
      180
      182.4 to 187.4
      200
      (202.7 to 207.7)

      Reference: (mph) 
      Intelligent tester indication (mph)
      Acceptable Range (mph)
      Data in ( ) is for reference
      20
      21.0 to 23.0
      40
      42.0 to 44.0
      60
      63.0 to 66.0
      80
      83.0 to 87.0
      100
      104.0 to 108.0
      120
      125.0 to 129.0
      140
      146.0 to 150.0
      160
      166.0 to 171.0
      180
      187.0 to 192.0
      200
      (208.0 to 213.0)

  1. CHECK LED ILLUMINATION (BULB CHECK)

    1. Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).

      OK:

      Warning or Indicator Light
      Specified Condition
      Master
      Warning or indicator light comes on for about 3 seconds after turning the power switch on (IG).
      SRS
      Warning light comes on for about 6 seconds after turning the power switch on (IG).
      Oil pressure
      Indicator or warning light comes on when turning the power switch on (IG).
      Charge
      EPS
      MIL (Check engine warning light)
      Brake
      1. Warning or indicator light comes on for about 3 seconds after turning the power switch on (IG).
      2. Indicator or warning light comes on for about 3 seconds when turning the power switch from off to on (READY).
      Slip
      ABS
      Electronically controlled brake