Home › Suspension › TIRE / WHEEL › TIRE AND WHEEL SYSTEM

TIRE AND WHEEL SYSTEM > INSPECTION

for Preparation Click here



1. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    1. Adjust the tire pressure

      Cold Tire Inflation Pressure:

      Tire Size
      Front
      kPa (kgf/cm2, psi)
      Rear
      kPa (kgf/cm2, psi)
      175/65R15 84H
      230 (2.3, 33)
      230 (2.3, 33)*1
      220 (2.2, 32)*2
      185/60R15 84H
      220 (2.2, 32)
      220 (2.2, 32)

      *1: for Australia
      *2: except Australia

    2. Perform initialization (Click here).

    3. Tire pressure adjustment method when warm (w/ Tire Pressure Warning System:)

      1. Turn the power switch off.
      2. Connect the GTS to the DLC3.
      3. Turn the power switch on (IG).
      4. Turn the GTS on.
      5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
      6. Adjust the tire pressure so that the displayed value is equal to the set pressure.
      7. Perform initialization and check that initialization completes (Click here).
      8. Check and record the value of the Data List item "Temperature in Tire". (Ts)
      9. Check and record the ambient temperature during tire pressure adjustment. (Tm)
      10. Readjust the tire pressure according to the difference between the tire internal temperature (Ts) and the ambient temperature (Tm). (P)

        HINT:
        Tire internal temperature: Ts, Ambient temperature: Tm, Tire pressure readjustment value: P
        P = (Specified Pressure) + (Ts - Tm)

      11. Check the pressure adjustment value with the Data List item "Tire Inflation Pressure".

      NOTICE:
      for ECE-R64 Type:
      If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.



    C164558
  1. Using a dial indicator, check the runout of the tires.

    Maximum tire runout:
    Vertical:
    1.4 mm (0.0551 in.)
    Lateral:
    2.0 mm (0.0787 in.)



2. ROTATE TIRES


    C143305E04
  1. If the spare tire uses a different type of wheel than the other tires, rotate the tires as shown by (A) in the illustration. If the spare tire has the same type of wheel as the other tires, rotate the tires, including the spare tire, as shown by (B) in the illustration.
    Text in Illustration 
    V100135
    Front

  1. Perform initialization (Click here)



3. INSPECT AND ADJUST WHEEL BALANCE


  1. Inspect and adjust the off-the-car balance.

    1. Steel wheel:

      Maximum imbalance:
      8.0 g (0.0176 lb)



    2. C144018E06
    3. Others (Non-steel wheel):

      Maximum imbalance:
      8.0 g (0.0176 lb)

      NOTICE:
      1. Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.
      2. Do not touch the adhesive surface of the tape.
      3. Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.

        Width (A):
        25 mm (0.984 in.)

      4. Push the balance weight securely with your finger to adhere it to the desired position.
      5. Do not reuse balance weights.

      HINT:
      The inner side balance weight should be installed by clipping it to the rim.



4. INSPECT FRONT AXLE HUB BEARING
(Click here)


5. INSPECT REAR AXLE HUB BEARING
(Click here)