Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > High Beam Headlight Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the high beam headlights via the DIM/DRL relay.

WIRING DIAGRAM


E246559E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Check that the high beam headlights illuminate.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light Hi
    High beam headlights
    ON/OFF
    -

    OK:
    The high beam headlights illuminate.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT DIM/DRL RELAY
  1. Remove the DIM/DRL relay from the No. 2 engine room relay block and No. 2 junction block assembly.



    E223988E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE DIM/DRL RELAY
OK


3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - DIM/DRL RELAY)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 2 - Body ground
    Power switch off
    11 to 14 V
    Relay terminal 3 - Body ground
    Power switch off
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (DIM/DRL RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
  1. for LED Headlight

    1. Disconnect the A55 headlight assembly LH connector.

    2. Disconnect the A54 headlight assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Relay terminal 5 - A55-2
      Always
      Below 1 Ω
      Relay terminal 5 - A54-2
      Always
      Below 1 Ω
      Relay terminal 5 - Body ground
      Always
      10 kΩ or higher

  1. for Halogen Headlight and w/ Rear Fog Light

    1. Disconnect the A2 headlight assembly LH connector.

    2. Disconnect the A1 headlight assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Relay terminal 5 - A2-2
      Always
      Below 1 Ω
      Relay terminal 5 - A1-2
      Always
      Below 1 Ω
      Relay terminal 5 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (DIM/DRL RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 1 - 3C-35
    Always
    Below 1 Ω
    3C-35 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).



    E182506E37
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-35 - MB-22 (DIM)
    Always
    Below 1 Ω
    3C-35 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)