Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > High Beam Headlight Circuit

for Preparation Click here


DESCRIPTION

When the main body ECU (multiplex network body ECU) receives a high beam turn on signal, the main body ECU (multiplex network body ECU) activates the bi-function by controlling the DIM/DRL relay. The bi-function increases the upper illumination area of the low beam by moving a shade using a solenoid built into the headlight assembly.

WIRING DIAGRAM


E308446E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light Hi
    High beam headlights
    ON/OFF
    -

    OK:
    High beam headlights illuminate.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT DIM/DRL RELAY
  1. Remove the DIM/DRL relay from the No. 2 engine room relay block and No. 2 junction block assembly.



    E223988E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Voltage applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE DIM/DRL RELAY
OK


3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - DIM/DRL RELAY)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 2 - Body ground
    Power switch off
    11 to 14 V
    Relay terminal 3 - Body ground
    Power switch off
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (DIM/DRL RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
  1. Disconnect the A69 headlight assembly LH connector.

  1. Disconnect the A68 headlight assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 5 - A69-3 (HI)
    Always
    Below 1 Ω
    Relay terminal 5 - A68-3 (HI)
    Always
    Below 1 Ω
    Relay terminal 5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (DIM/DRL RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 1 - 3C-35
    Always
    Below 1 Ω
    3C-35 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).



    E182506E37
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-35 - MB-22 (DIM)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)