Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER

FRONT SHOCK ABSORBER > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. INSTALL FRONT COIL SPRING LOWER INSULATOR (w/ Front Coil Spring Lower Insulator)


    C312092E01
  1. Install the front coil spring lower insulator to the front shock absorber assembly.
    Text in Illustration 
    *a
    Positioning Pin
    *b
    Hole



2. INSTALL FRONT COIL SPRING


    C235694E01
  1. Using SST, compress the front coil spring.

    SST
    09727-30021   (09727-00010, 09727-00021, 09727-00031)
    Text in Illustration 
    *a
    Lower End

    NOTICE:
    Do not use an impact wrench. It will damage SST.

  1. Install the front coil spring onto the front shock absorber assembly.

    NOTICE:
    Make sure to fit the end of the spring that has the larger diameter into the front shock absorber lower seat.

    HINT:
    Fit the lower end of the front coil spring into the gap of the front shock absorber lower seat.



3. INSTALL FRONT COIL SPRING UPPER INSULATOR


4. INSTALL FRONT NO. 1 SPRING BUMPER SUB-ASSEMBLY (w/ Front Coil Spring Lower Insulator)


  1. Install the front No. 1 spring bumper sub-assembly to the front shock absorber assembly.

    NOTICE:
    C309985E01
    When installing the front No. 1 spring bumper sub-assembly, first align the hole in the front No. 1 spring bumper sub-assembly with the protrusion of the front coil spring upper insulator.

    Text in Illustration 
    *a
    Hole
    *b
    Protrusion



5. INSTALL FRONT NO. 1 SPRING BUMPER SUB-ASSEMBLY (w/o Front Coil Spring Lower Insulator)
  1. Install the front No. 1 spring bumper sub-assembly to the front shock absorber assembly.



6. INSTALL FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT
  1. Temporarily tighten a new front support to front shock absorber nut.

  1. Remove SST from the front coil spring.

    NOTICE:
    Do not use an impact wrench. It will damage SST.



    C229624E05
  1. Using SST and long hexagon socket wrench, hold the shock absorber rod and tighten the front support to front shock absorber nut.

    SST
    09729-97202  
    Text in Illustration 
    *1
    Long Hexagon Socket Wrench
    *a
    Hold
    *b
    Turn

    Torque:
    without SST:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }
    with SST:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    HINT:
    1. This torque value is effective when SST is parallel to the torque wrench.
    2. This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and SST with a fulcrum length of 40 mm (1.57 in.).
    3. If using a torque wrench with a length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).



7. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY


8. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    C235028
  1. Temporarily tighten a new nut through the front No. 2 suspension support.

  1. Install the front shock absorber with coil spring to the steering knuckle and insert the 2 bolts and 2 nuts.

    Torque:
    164 N*m{ 1672 kgf*cm , 121 ft.*lbf }

    NOTICE:
    When installing the nuts, keep the bolts from rotating.

    HINT:
    The bolt can be inserted in either direction, however, make sure that they are installed in the same direction.



9. INSTALL FRONT FLEXIBLE HOSE
  1. Install the front flexible hose and front speed sensor with the bolt.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }

    NOTICE:
    Do not twist the front flexible hose and front speed sensor when installing it.



10. INSTALL FRONT STABILIZER LINK ASSEMBLY
  1. Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    Use a hexagon socket wrench to hold the stud.



11. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



12. FULLY TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING


    C252476E01
  1. Using SST and long hexagon socket wrench, hold the front shock absorber rod and tighten the nut.

    SST
    09729-97202  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

    Torque:
    with SST:
    55 N*m{ 561 kgf*cm , 41 ft.*lbf }
    without SST:
    49 N*m{ 503 kgf*cm , 36 ft.*lbf }

    HINT:
    1. This torque value is effective when SST is parallel to the torque wrench.
    2. This torque value can be obtained by using a torque wrench with a fulcrum length of 345 mm (1.13 ft.) and SST with a fulcrum length of 40 mm (1.57 in.).
    3. If using a torque wrench with a length that is not 345 mm (1.13 ft.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).



13. INSTALL FRONT SUSPENSION SUPPORT DUST COVER


14. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C250015E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the clamp to install the wire harness.



15. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C249838E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the 3 clamps to install the wire harness.



16. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



17. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



18. INSTALL FRONT AIR SHUTTER SEAL (for LHD)
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



19. INSTALL FRONT AIR SHUTTER SEAL (for RHD)
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



20. INSTALL INNER COWL TOP TO COWL BRACE (for LHD)


    C250011E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



21. INSTALL INNER COWL TOP TO COWL BRACE (for RHD)


    C249834E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



22. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY



23. STABILIZE SUSPENSION
  1. Lower the vehicle.

  1. Bounce the vehicle up and down several times to stabilize the suspension.



24. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)