Home › Suspension › REAR SUSPENSION › REAR COIL SPRING

REAR COIL SPRING > REMOVAL

for Preparation Click here


CAUTION:
Before removing the rear axle beam assembly, make sure to support the front suspension crossmember sub-assembly using a jack or equivalent. If the rear axle beam assembly is removed without the vehicle supported, the front-to-rear weight distribution will become unbalanced and may cause the vehicle to fall off the lift.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C250008
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



3. REMOVE REAR WHEELS


4. DRAIN BRAKE FLUID

NOTICE:
Immediately wash off any brake fluid that comes into contact with any painted surfaces.



5. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)
(Click here)


6. DISCONNECT SKID CONTROL SENSOR WIRE LH


    C249819
  1. Disengage the 3 claws and remove the connector cover.



    C249820
  1. Disconnect the skid control sensor wire connector from the rear axle hub and bearing assembly.



7. DISCONNECT SKID CONTROL SENSOR WIRE RH

HINT:
Perform the same procedure as the LH side.



8. SEPARATE SKID CONTROL SENSOR WIRE LH


    C107566
  1. Remove the nut and separate the skid control sensor wire LH.



9. SEPARATE SKID CONTROL SENSOR WIRE RH

HINT:
Perform the same procedure as the LH side.



10. SEPARATE REAR FLEXIBLE HOSE LH


    C235742
  1. Using a union nut wrench, separate the brake tube while holding the rear flexible hose LH with a wrench.

    NOTICE:
    1. Do not bend or damage the brake line.
    2. Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

  1. Remove the clip and separate the rear flexible hose LH from the rear axle beam assembly.



11. SEPARATE REAR FLEXIBLE HOSE RH

HINT:
Perform the same procedure as the LH side.



12. LOOSEN REAR AXLE BEAM ASSEMBLY


    C249958E01
  1. Loosen the 2 bolts.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side

    NOTICE:
    Do not remove the 2 bolts.



13. REMOVE REAR COIL SPRING LH


  1. Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.


    C249968E01


    Text in Illustration 
    *1
    Wooden Block
    *2
    Jack

  1. Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

    NOTICE:
    Since stopper nuts are used, turn the bolts.

  1. Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks, and remove the rear coil spring LH.

  1. Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.

    NOTICE:
    Since stopper nuts are used, turn the bolts.



14. REMOVE REAR COIL SPRING RH

HINT:
Perform the same procedure as the LH side.



15. REMOVE REAR UPPER COIL SPRING INSULATOR LH


16. REMOVE REAR UPPER COIL SPRING INSULATOR RH


17. REMOVE REAR LOWER COIL SPRING INSULATOR LH


18. REMOVE REAR LOWER COIL SPRING INSULATOR RH