Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > INSTALLATION

for Preparation Click here


HINT:
Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.



1. INSTALL NO. 1 PARKING BRAKE CABLE CLAMP
  1. Engage the 2 claws to install a new No. 1 parking brake cable clamp to the No. 3 parking brake cable assembly.



2. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


  1. Install the No. 3 parking brake cable assembly with the 4 bolts.


    C249928E01

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Engage clamp A to install the No. 3 parking brake cable assembly.

    NOTICE:
    Securely install the clamp.

  1. Insert the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly into new clamp B and install clamp B to the vehicle.

  1. Install the No. 3 parking brake cable assembly onto the backing plate with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the No. 3 parking brake cable assembly to the parking brake equalizer.

  1. Engage the 2 claws to install the parking brake cable stopper.



3. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for RH Side)
  1. Install the No. 1 fuel tank protector sub-assembly with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Install the clip.



4. INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR (for RH Side)


    C247550E01
  1. Install the front No. 4 floor heat insulator with the 2 nuts.

    Torque:
    Nut A:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut B:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



5. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY



6. ADJUST PARKING BRAKE LEVER TRAVEL
  1. Release the parking brake lever lock and return it to its off position.

  1. Remove the rear console box (Click here).

  1. Remove the No. 1 console box mounting bracket .

  1. Remove the No. 3 console box mounting bracket .



    C247540E01
  1. Turn the lock nut until the parking brake lever travel is corrected to within the specified range.
    Text in Illustration 
    *1
    Lock nut

    Parking brake lever travel:
    8 to 11 notches at 200 N (20 kgf, 45.0 lbf)

    NOTICE:
    If the lock nut has been removed from the rod, replace the lock nut with a new one.

  1. Operate the parking brake lever 3 to 4 times, and check the parking brake lever travel.

  1. Check that the parking brake does not drag.

  1. Install the No. 3 console box mounting bracket .

  1. Install the No. 1 console box mounting bracket .

  1. Install the rear console box (Click here).



7. INSTALL NO. 3 CONSOLE BOX MOUNTING BRACKET


    C251698E01
  1. Install the No. 3 console box mounting bracket with the bolt.
    Text in Illustration 
    *a
    Stopper

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    NOTICE:
    Securely install the No. 3 console box mounting bracket so that its stopper contacts the parking brake lever support bracket as shown in the illustration.



8. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET


    C251697
  1. Install the No. 1 console box mounting bracket with the 3 bolts.



9. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)