Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).



2. REMOVE FRONT FLOOR COVER RH


    B301488E01
  1. Using a clip remover, remove the 2 clips <A>.

  1. Disengage the 3 clips <B>.



    B301489
  1. Disengage the 3 guides and remove the front floor cover RH.



3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B307078
  1. Disengage the 10 claws and 4 guides.

  1. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.



5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B307079
  1. Disengage the 10 claws and 4 guides.

    1. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.



6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B307080E01
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and open the cover.
    Text in Illustration 
    *1
    Protective Tape



    B307081
  1. Remove the 3 screws.



    B307082
  1. Disengage the 8 clips and remove the front door trim board sub-assembly as shown in the illustration.



    B307083E01
  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable from the front door trim board sub-assembly.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly



7. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B307084
  1. Disengage the 4 guides and remove the front door inside handle sub-assembly.



8. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP


    B307085
  1. Disengage the 8 claws as show in the illustration and remove the front door glass inner weatherstrip.



9. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER


    B307652
  1. Disconnect the connector.

  1. Remove the 3 screws.

  1. Disengage the claw and remove the outer rear view mirror assembly with cover.



10. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    E237140
  1. Disconnect the connector.



    E237141
  1. Using a drill bit with a diameter of less than 5 mm (0.197 in.), drill out the 3 rivet heads and remove the front No. 1 speaker assembly.

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. Do not drill the rivet at an angle as this will cause damage to the drill and drill hole. Line up the drill and rivet, and carefully drill out the rivet head.
    3. Be careful as the cut rivet will be very hot.

  1. Continue drilling and push out the remaining rivet fragments.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.



11. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY


    E237142
  1. Disconnect the connector.

  1. Remove the 2 screws and front No. 2 speaker assembly.



12. REMOVE FRONT DOOR SERVICE HOLE COVER


    B308297
  1. Remove the front door service hole cover.

    NOTICE:
    Remove any remaining butyl tape from the front door panel.



13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B307087
  1. Remove the front door No. 2 service hole cover.

  1. Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the negative (-) auxiliary battery terminal and power window regulator master switch assembly.



    B307088
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door glass to fall.



    B307089
  1. Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.



14. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    B307090E01
  1. Disconnect the connector.

  1. Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door power window regulator assembly may fall and cause damage.

  1. Remove the 5 bolts and front door window regulator assembly.

  1. Remove the temporary bolt from the front door window regulator assembly.



15. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B307091
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.



16. REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY


    B298004E01
  1. Apply protective tape to the door panel in the area around the front door glass outer weatherstrip assembly.
    Text in Illustration 
    *1
    Protective Tape



    B297999E01
  1. Using a screwdriver with the tip wrapped with protective tape, disengage the 5 claws.
    Text in Illustration 
    *1
    Protective Tape

  1. Disengage the guide and remove the front door glass outer weatherstrip assembly.



17. REMOVE FRONT DOOR GLASS RUN


    B307092
  1. Remove the front door glass run.



18. REMOVE FRONT DOOR CHECK ASSEMBLY


    B307093
  1. Remove the 3 bolts and the front door check assembly.



19. REMOVE FRONT DOOR WEATHERSTRIP


    B307094
  1. Disengage the 30 clips and remove the front door weatherstrip.



20. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B307095
  1. Remove the bolt.

  1. Disengage the guide and remove the front door rear lower frame sub-assembly.



21. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    B307096
  1. Remove the screw.

  1. Remove the 2 bolts and remove the front door front lower frame sub-assembly.



22. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP


    B307097
  1. Slide the front door fix window weatherstrip, in the direction indicated by the arrow in the illustration, to remove it.

  1. Remove the front door fix window glass from the front door fix window weatherstrip.



23. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B299844
  1. Remove the hole plug.



    B307098
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B307099
  1. Using a screwdriver, disengage the claw and 2 guides to remove the front door outside handle cover as shown in the illustration.



25. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    B297584
  1. Remove the hole plug.



    B300049
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



26. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B307100
  1. Using a screwdriver, disengage the 3 claws and disconnect the connector as shown in the illustration.



    B307101
  1. Remove the front door outside handle assembly as shown in the illustration.



27. REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD


    B307102
  1. Disengage the 3 claws and remove the front door outside handle front pad.



28. REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD


    B307103
  1. Disengage the 2 claws and remove the front door outside handle rear pad.



29. REMOVE FRONT DOOR LOCK ASSEMBLY


    B307104E01
  1. Disconnect the connector.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

  1. Using a T30 "TORX" socket wrench, remove the 3 screws.

  1. Move the front door lock assembly downward and disconnect the front door lock open rod, and then remove the front door lock assembly.



  1. When reusing the front door lock assembly:



      B307105
    1. Remove the door lock wiring harness seal from the front door lock assembly.



30. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B307106
  1. Remove the front door lock remote control cable assembly as shown in the illustration.



31. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B307107
  1. Using a screwdriver, disengage the 3 claws as shown in the illustration.



    B307108
  1. Remove the front door inside locking cable assembly as shown in the illustration.



32. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B307109E01
  1. Using a T30 "TORX" socket wrench, loosen the screw.
    Text in Illustration 
    *a
    Outside
    *b
    Inside

  1. Slide the front door outside handle frame sub-assembly to disengage the door handle nut and 2 claws of the front door outside handle frame sub-assembly, and then remove it.



    B307110
  1. Remove the front door outside handle frame sub-assembly with the wire as shown in the illustration.

  1. Disengage the 2 clamps and guide and remove the front door outside handle frame sub-assembly.



33. REMOVE FRONT DOOR LOCK OPEN ROD


    B307111E01
  1. Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.



34. REMOVE FRONT DOOR PANEL CUSHION


    B307112
  1. Disengage each claw and remove the 2 front door panel cushions.



35. REMOVE NO. 1 BLACK OUT TAPE
  1. Using a heat light, heat the No. 1 black out tape and vehicle body.
    Heating Temperature 
    Item
    Temperature
    No. 1 Black Out Tape and Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B298010
  1. Pull back on one of the ends of the No. 1 black out tape to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.