Home › Engine / Hybrid System › 1NZ-FXE ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REASSEMBLY

for Preparation Click here



1. INSTALL VALVE SPRING SEAT
  1. Install the 16 valve spring seats to the cylinder head sub-assembly.



2. INSTALL VALVE STEM OIL SEAL


    A267437E01
  1. Apply a light coat of engine oil to a new valve stem oil seal.
    Text in Illustration 
    *a
    Intake Side
    *b
    Exhaust Side
    *c
    Gray
    *d
    Black

    NOTICE:
    Pay close attention when installing the intake and exhaust valve stem oil seals. For example, installing the intake valve stem oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side can cause installation problems later.



    A265781E01
  1. Using SST, push on the 16 valve stem oil seals.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    SST
    09201-41020  

    NOTICE:
    Failure to use SST will cause the seal to be damaged or improperly seated.



3. INSTALL INTAKE VALVE


    A094935E41
  1. Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. Install the 8 intake valves, 8 compression springs and 8 retainers to the cylinder head sub-assembly.

    NOTICE:
    Install the same parts in the same combination to their original locations.



    A265772E01
  1. Using SST and wooden blocks, compress the compression spring and install the 8 retainer locks.

    SST
    09202-70020   (09202-00010, 09202-01010, 09202-01020)



    A037146
  1. Using a pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the valve stem tip.



4. INSTALL EXHAUST VALVE


    A094936E36
  1. Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. Install the 8 exhaust valves, 8 compression springs and 8 retainers to the cylinder head sub-assembly.

    NOTICE:
    Install the same parts in the same combination to their original locations.



    A265773E01
  1. Using SST and wooden blocks, compress the compression spring and install the 8 retainer locks.

    SST
    09202-70020   (09202-00010, 09202-01010, 09202-01020)



    A265782
  1. Using a pin punch and plastic hammer, lightly tap the valve stem tip to ensure a proper fit.

    NOTICE:
    Be careful not to damage the valve stem tip.



5. INSTALL VALVE LIFTER
  1. Apply a light coat of engine oil to the valve lifters.



    A088718E02
  1. Install the 16 valve lifters.

    NOTICE:
    Install the same parts in the same combination to their original locations.

  1. Check that the valve lifters rotate smoothly by hand.



6. INSTALL OIL CONTROL VALVE FILTER
  1. Check that no foreign matter is on the mesh part of the oil control valve filter.



    A050664E12
  1. Using an 8 mm hexagon wrench, install the oil control valve filter with a new gasket and the straight screw plug.
    Text in Illustration 
    *a
    Mesh Part

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



7. INSTALL TAPER SCREW PLUG
  1. Install a new gasket to the taper screw plug.



    A088717E02
  1. Using a 10 mm hexagon wrench, install the taper screw plug.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }