Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH

OUTER MIRROR SWITCH > INSPECTION

for Preparation Click here



1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retractable Mirror)


    B127217E04
  1. Check the resistance.
    Text in Illustration 
    *1
    Left / Right Select Switch
    *2
    Adjustment Switch
    *a
    Component without harness connected
    (Outer Mirror Switch Assembly)

    1. Select "L" on the left/right select switch.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      4 (VL) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      4 (VL) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (HL) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      5 (HL) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch.

    3. Select "R" on the left/right select switch.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      3 (VR) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      3 (VR) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (HR) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher
      2 (HR) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Pressed
      Below 1 Ω
      Not pressed
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch assembly.



2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retractable Mirror)


  1. Check the mirror select switch and mirror surface adjust switch.



      B254629E16
    1. Turn the mirror select switch to the L position.

    2. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *1
      Mirror select switch
      *2
      Mirror surface adjust switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

      Standard Resistance (for left side):
      Tester Connection
      Switch Condition
      Specified Condition
      4 (VL) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      4 (VL) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      5 (HL) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      5 (HL) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

    3. Turn the mirror select switch to the R position.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (for right side):
      Tester Connection
      Switch Condition
      Specified Condition
      3 (VR) - 8 (B)
      6 (M+) - 7 (E)
      UP
      Below 1 Ω
      OFF
      10 kΩ or higher
      3 (VR) - 7 (E)
      6 (M+) - 8 (B)
      DOWN
      Below 1 Ω
      OFF
      10 kΩ or higher
      2 (HR) - 8 (B)
      6 (M+) - 7 (E)
      LEFT
      Below 1 Ω
      OFF
      10 kΩ or higher
      2 (HR) - 7 (E)
      6 (M+) - 8 (B)
      RIGHT
      Below 1 Ω
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the outer mirror switch assembly.



  1. Check the mirror retract switch.



      B254629E05
    1. Measure the resistance according to the value(s) in the table below.
      Text in Illustration 
      *1
      Mirror retract switch
      *a
      Component without harness connected
      (Outer Mirror Switch Assembly)

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      10 (MF) - 7 (E)
      Mirror retract switch retract position
      Below 1 Ω
      9 (MR) - 8 (B)
      Below 1 Ω
      10 (MF) - 8 (B)
      Mirror retract switch return position
      Below 1 Ω
      9 (MR) - 7 (E)
      Below 1 Ω

      If the result is not as specified, replace the outer mirror switch assembly.