FUEL SYSTEM > PRECAUTION |
| 1.PRECAUTIONS |
Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) auxiliary battery terminal.
Perform the Discharge Fuel System Pressure procedure below before disconnecting a fuel line to prevent gasoline from spilling out.
Keep gasoline away from rubber or leather parts.
| 2.DISCHARGE FUEL SYSTEM PRESSURE |
Remove the rear seat cushion assembly (Click here).
Remove the rear floor service hole cover.
![]() |
Disconnect the connector from the fuel suction tube with pump and gauge assembly.
Put the engine in inspection mode (Click here).
Start the engine.
After the engine has stopped on its own, turn the power switch off.
Crank the engine again and make sure that the engine does not start.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.
Connect the fuel pump connector.
Install the rear floor service hole cover with new butyl tape.
Install the rear seat cushion assembly (Click here).
| 3.FUEL SYSTEM |
When disconnecting a high pressure fuel line, a large amount of gasoline will spill out, so perform the following procedure:
Discharge the fuel system pressure.
Disconnect the fuel tank main tube sub-assembly.
Drain the fuel remaining inside the fuel tank main tube sub-assembly into a container.
Cover the disconnected pipe and connector with plastic bags to prevent damage and contamination.
Put a container under the connecting parts.
Perform the following procedure when disconnecting the fuel tube connector (quick type A):
![]() |
Remove the No. 1 fuel pipe clamp.
Check whether there is any foreign matter on the fuel pipe around the fuel tube connector before disconnecting it and remove the foreign matter as necessary.
![]() |
Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.
| *1 | Retainer |
| *2 | Nylon Tube |
| *3 | Fuel Pipe |
| *4 | O-ring |
| *5 | Fuel Tube Connector |
![]() | Pinch |
![]() | Pull Out |
![]() |
If the fuel tube connector and the fuel pipe are stuck, push in and pull on the fuel tube connector to release it. Pull the fuel tube connector out of the fuel pipe carefully.
![]() | Pull |
![]() | Push |
Check that there is no dirt or other foreign matter on the sealing surfaces of the disconnected fuel pipes. Clean the surfaces if necessary.
Cover the disconnected fuel pipe and fuel tube connector with a plastic bag to prevent damage and contamination.
![]() |
Perform the following procedure when connecting a fuel tube connector (quick type A):
![]() | Push |
Check if there is any damage or foreign matter on the connecting parts of the fuel pipes.
Line up the 2 parts of the fuel pipes to be connected, and push them together until the fuel tube connector makes a "click" sound.
![]() |
After connecting the fuel pipes, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
![]() | Pull |
Inspect for fuel leaks .
Install the No. 1 fuel pipe clamp.
![]() |
Perform the following procedure when disconnecting a fuel tube connector (quick type B):
| *1 | Retainer |
![]() | Pull |
![]() | Pull Out |
Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.
Pull the tabs of the retainer to disengage the lock claws and pull out the fuel tube connector from the fuel pipe.
![]() |
If the fuel tube connector and the fuel pipe are stuck, push in and pull on the fuel tube connector to release it. Pull the fuel tube connector out of the fuel pipe carefully.
![]() | Pull |
![]() | Push |
Check that there is no dirt or other foreign matter on the sealing surfaces of the disconnected fuel pipes. Clean the surfaces if necessary.
Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.
![]() |
Perform the following procedure when connecting the fuel tube connector (quick type B):
| *1 | Retainer |
![]() | Push |
![]() | Push |
Check if there is any damage or foreign matter on the connecting parts of the fuel pipes.
Line up the pipe and connector and push them together until a "click" sound is heard. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
After connecting the fuel pipes, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
Inspect for fuel leaks .
| 4.INJECTOR |
![]() |
Install the injector to the delivery pipe and the cylinder head as shown in the illustration.
| *1 | Delivery pipe |
| *2 | O-ring |
| *3 | Injector Vibration Insulator |
![]() |
Observe the following precautions when removing and installing the fuel injector.
| *1 | O-ring |
| *2 | Delivery pipe |
| *a | CORRECT |
| *b | INCORRECT |
Do not reuse the O-ring and insulator.
When placing a new O-ring on the injector, do not damage the O-ring.
Coat a new O-ring with spindle oil or gasoline before installing it.
| 5.FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY |
![]() |
Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is welded to the plate.
| *1 | Tube |
| 6.INSPECT FOR FUEL LEAK |
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs .