Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY

FRONT DRIVE SHAFT ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP


  1. for One Touch Type:



      C067083
    1. Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot clamp and separate the front No. 2 axle inboard joint boot clamp as shown in the illustration.



  1. for Claw Engagement Type:



      C157518E03
    1. Using needle-nose pliers, disengage the 2 claws and remove the front No. 2 axle inboard joint boot clamp as shown in the illustration.
      Text in Illustration 
      *a
      Claws



2. SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:
Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.



3. SEPARATE INBOARD JOINT BOOT
  1. Separate the inboard joint boot from the front drive inboard joint assembly.



4. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Remove the old grease from the front drive inboard joint assembly.



    C160821E13
  1. Put matchmarks on the front drive inboard joint assembly and front axle outboard joint shaft assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Do not use a punch for the marks.

  1. Remove the front drive inboard joint assembly from the front axle outboard joint shaft assembly.

  1. Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C160822
  1. Using a snap ring expander, remove the shaft snap ring from the front axle outboard joint shaft assembly.



    C162724E05
  1. Put matchmarks on the front axle outboard joint shaft assembly and tripod joint.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Do not use a punch for the marks.

  1. Using a brass bar and a hammer, tap out the tripod joint from the front axle outboard joint shaft assembly.

    NOTICE:
    1. Do not tap the rollers.
    2. Do not drop the tripod joint.

  1. Remove the front No. 2 axle inboard joint boot clamp, inboard joint boot and front axle inboard joint boot clamp.



5. SEPARATE DRIVE SHAFT DAMPER SETTING CLAMP (w/ 1 Clamp)


    C135385E09
  1. for One Touch Type:

    1. Using a screwdriver, release the staked part of the drive shaft damper setting clamp and separate the drive shaft damper setting clamp as shown in the illustration.
      Text in Illustration 
      *A
      for One Touch Type
      *B
      for Claw Engagement Type
      *a
      Claws

  1. for Claw Engagement Type:

    1. Using needle-nose pliers, disengage the 2 claws and remove the drive shaft damper setting clamp as shown in the illustration.



6. REMOVE DRIVE SHAFT DAMPER (w/ 1 Clamp)
  1. Remove the drive shaft damper and drive shaft damper setting clamp from the front axle outboard joint shaft assembly.



7. SEPARATE DRIVE SHAFT DAMPER (w/ 2 Clamps)


    C205160E01
  1. Using needle-nose pliers, disengage the 2 claws and separate the 2 drive shaft damper setting clamps as shown in the illustration.
    Text in Illustration 
    *a
    Claws



8. REMOVE DRIVE SHAFT DAMPER SETTING CLAMP (w/ 2 Clamps)
  1. Remove the drive shaft damper and 2 drive shaft damper setting clamps from the front axle outboard joint shaft assembly.



9. SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP


    C249940
  1. Using a screwdriver, release the staked part of the front No. 2 axle outboard joint boot clamp and separate the front No. 2 axle outboard joint boot clamp as shown in the illustration.



10. SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP

HINT:
Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.



11. REMOVE OUTBOARD JOINT BOOT
  1. Remove the front axle outboard joint boot clamp, outboard joint boot and front No. 2 axle outboard joint boot clamp from the front axle outboard joint shaft assembly.

  1. Remove the old grease from the outboard joint.



12. REMOVE FRONT DRIVE SHAFT DUST COVER


    F040647E07
  1. Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.

    SST
    09950-00020  

    NOTICE:
    Do not drop the front drive inboard joint assembly.