CHILD RESTRAINT SEAT ANCHOR BRACKET > INSTALLATION |
| 1. INSTALL CROSS ANCHOR BRACKET SUB-ASSEMBLY |
Temporarily install the cross anchor bracket sub-assembly with the bolt shown in the illustration.

Install the bolt and tighten the 2 bolts in the order shown in the illustration.

| 2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH |
Engage the guide, 4 claws and 4 clips.

| *1 | Rear Seatback Hinge | - | - |
Install the deck trim side panel assembly LH with the bolt and 2 screws.
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.
| 3. INSTALL REAR ABSORBER CAP LH |
Engage the 2 guides and 2 claws to install the rear absorber cap LH.
| 4. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the claw to install the No. 1 luggage compartment light assembly.
| 5. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
Engage the 2 claws.
Install the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.
| 6. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH |
| 7. INSTALL REAR ABSORBER CAP RH |
| 8. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH |
| 9. INSTALL REAR DECK TRIM COVER |
Engage the 2 guides and 4 claws.
Install the rear deck trim cover with the 2 clips.
| 10. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY |
Install the package tray trim panel assembly.
| 11. INSTALL DECK FLOOR BOX LH |
Install the deck floor box LH.
| 12. INSTALL DECK FLOOR BOX RH |
| 13. INSTALL DECK BOARD ASSEMBLY |
Install the deck board assembly.
| 14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *a | Alignment Mark (White) |
| *b | Flange Position |
| 15. INSTALL REAR DOOR SCUFF PLATE LH |
Engage the guide and the 5 claws to install the rear door scuff plate.
| 16. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| *a | Alignment Mark (Red) |
| *b | Flange Position |
| 17. INSTALL REAR DOOR SCUFF PLATE RH |
| 18. INSTALL REAR SEAT CUSHION ASSEMBLY |
Place the rear seat cushion assembly in the cabin.
![]() |
Push out the seat belt buckles from the back of the rear seat cushion assembly so that they are positioned as shown in the illustration.
![]() |
Engage the hook of the rear seat cushion assembly to the CRS anchor bracket.
![]() |
Engage the 2 rear seat cushion lock hooks to install the rear seat cushion assembly as shown in the illustration.
Confirm that the seat cushion is firmly installed.
Engage the 2 clips.
| 19. INSTALL REAR SEATBACK ASSEMBLY LH |
Place the rear seatback assembly LH in the cabin.
Install the rear seatback assembly LH with the 2 bolts.
Raise the rear seatback assembly LH.
| 20. INSTALL REAR SEATBACK ASSEMBLY RH |
Place the rear seatback assembly RH in the cabin.
Install the rear seatback assembly RH with the 2 bolts.
Raise the rear seatback assembly RH.
| 21. INSTALL FRONT CENTER FLOOR COVER |
Engage the 2 guides to install the front center floor cover.
Install the 3 clips.
| 22. INSTALL FRONT FLOOR COVER LH |
Engage the 3 guides.
![]() |
Engage the clip <B> to install the front floor cover LH.
Install the 2 clips <A>.
| 23. INSTALL FRONT FLOOR COVER RH |
Engage the 3 guides.
![]() |
Engage the clip <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 24. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY |
| 25. INSTALL REAR SEAT HEADREST ASSEMBLY |