FRONT AXLE HUB > INSTALLATION |
| 1. INSTALL FRONT AXLE HUB BEARING |
![]() |
Using SST and a press, insert a new front axle hub bearing, with its magnetic rotor side facing the inside of the vehicle, until it reaches the end of the steering knuckle.
![]() | Inside of the Vehicle |
![]() | Magnetic Rotor Side |
| 2. INSTALL FRONT AXLE HUB SUB-ASSEMBLY |
![]() |
Using SST and a press, press the axle hub into the steering knuckle.
| 3. INSTALL FRONT AXLE HUB HOLE SNAP RING |
![]() |
Using snap ring pliers, install a new front axle hub hole snap ring, as shown in the illustration.
| *a | Speed Sensor Installation Gap |
| 4. INSTALL FRONT AXLE ASSEMBLY |
Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.
| 5. INSTALL FRONT DRIVE SHAFT ASSEMBLY |
![]() |
Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and install the front drive shaft assembly to the front axle hub sub-assembly.
| *a | Matchmark |
| 6. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY |
Install the front lower No. 1 suspension arm sub-assembly LH to the steering knuckle with a new nut.
Install a new clip.
| 7. CONNECT TIE ROD END SUB-ASSEMBLY |
![]() |
Connect the tie rod end sub-assembly LH to the steering knuckle with a new nut.
Install a new cotter pin.
| 8. INSTALL FRONT DISC |
![]() |
Align the matchmarks of the disc and axle hub, and install the front disc.
| *a | Matchmark |
| 9. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY |
Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.
| 10. TEMPORARILY INSTALL FRONT AXLE SHAFT NUT |
Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using a non-residue solvent.
Using a socket wrench (30 mm), while applying the brakes, temporarily install the front axle shaft nut.
| 11. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY |
Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.
| 12. REMOVE FRONT DISC |
![]() |
Remove the front disc.
| *a | Matchmark |
| 13. INSPECT FRONT AXLE HUB BEARING LOOSENESS |
![]() |
Using a dial indicator, check for looseness near the center of the front axle hub sub-assembly.
| 14. INSPECT FRONT AXLE HUB RUNOUT |
![]() |
Using a dial indicator, check for runout on the surface of the front axle hub sub-assembly outside the front axle hub bolts.
| 15. INSTALL FRONT DISC |
![]() |
Align the matchmarks of the disc and axle hub, and install the front disc.
| *a | Matchmark |
| 16. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY |
Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.
| 17. INSTALL FRONT SPEED SENSOR |
Install the front speed sensor wire and front flexible hose to the front shock absorber assembly with the bolt.
Install the front speed sensor to the steering knuckle with the bolt.
| 18. INSTALL FRONT AXLE SHAFT NUT |
![]() |
Using a chisel and hammer, stake the front axle shaft nut.
| 19. INSTALL FRONT WHEEL |
| 20. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
Connect the cable to the negative (-) auxiliary battery terminal .
Connect the reservoir level switch connector.
Clear the DTCs (Click here).
| 21. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 22. CHECK FOR SPEED SENSOR SIGNAL |