Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM

WIRELESS DOOR LOCK CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B281049E03


Text in Illustration 
*A
Main body ECU (multiplex network body ECU) with 1 connector
*B
for LHD
*C
for RHD
-
-
*1
Main body ECU (multiplex network body ECU)
-
-

B297238E01


Text in Illustration 
*A
Main body ECU (multiplex network body ECU) with 2 connectors
*B
for LHD
*C
for RHD
-
-
*1
Main body ECU (multiplex network body ECU)
-
-
  1. Disconnect the MB main body ECU (multiplex network body ECU) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    MB-11 (GND1) - Body ground
    -
    Ground
    Always
    Below 1 Ω
    MB-30 (BECU) - Body ground
    -
    Auxiliary battery power supply
    Power switch off
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    MB-29 (ACC) - Body ground
    -
    ACC power supply
    Power switch off
    Below 1 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    Power switch on (IG)
    11 to 14 V
    MB-32 (IG) - Body ground
    -
    IG power supply
    Power switch off
    Below 1 V

  3. Reconnect the MB main body ECU (multiplex network body ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    3B-3 (ACT-) - Body ground
    R - Body ground
    Door lock motor unlock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3B-3 (ACT-) - Body ground
    R - Body ground
    Door lock motor unlock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked
    11 to 14 V
    3B-1 (ACT+) - Body ground
    Y - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder off
    Below 1 V
    3B-1 (ACT+) - Body ground
    Y - Body ground
    Door lock motor lock drive output (all doors)
    Door control switch (power window regulator master switch assembly) or driver door key cylinder locked
    11 to 14 V
    3D-36 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy light switch input
    Front door LH open
    Below 1 V
    3D-36 (FLCY) - Body ground
    R - Body ground
    Front door LH courtesy light switch input
    Front door LH closed
    Pulse generation
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door RH courtesy light switch input
    Front door RH open
    Below 1 V
    G59-19 (FRCY) - Body ground
    R - Body ground
    Front door RH courtesy light switch input
    Front door RH closed
    Pulse generation
    G59-24 (LCTY) - Body ground
    L - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    G59-24 (LCTY) - Body ground
    L - Body ground
    Rear door LH courtesy light switch input
    Rear door LH closed
    Pulse generation
    G59-6 (RCTY) - Body ground
    G - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    G59-6 (RCTY) - Body ground
    G - Body ground
    Rear door RH courtesy light switch input
    Rear door RH closed
    Pulse generation
    G59-7 (LSFL) - Body ground
    L - Body ground
    Front door LH unlock detection switch input
    Front door LH unlocked
    Below 1 V
    G59-7 (LSFL) - Body ground
    L - Body ground
    Front door LH unlock detection switch input
    Front door LH locked
    Pulse generation
    G59-18 (LSFR) - Body ground
    L - Body ground
    Front door RH unlock detection switch input
    Front door RH unlocked
    Below 1 V
    G59-18 (LSFR) - Body ground
    L - Body ground
    Front door RH unlock detection switch input
    Front door RH locked
    Pulse generation
    3D-25 (LSR) - Body ground
    V - Body ground
    Rear door RH unlock detection switch input
    Rear door RH unlocked
    Below 1 V
    3D-25 (LSR) - Body ground
    V - Body ground
    Rear door RH unlock detection switch input
    Rear door RH locked
    Pulse generation
    3D-24 (LSR) - Body ground
    Y - Body ground
    Rear door LH unlock detection switch input
    Rear door LH unlocked
    Below 1 V
    3D-24 (LSR) - Body ground
    Y - Body ground
    Rear door LH unlock detection switch input
    Rear door LH locked
    Pulse generation
    3C-34 (BZR) - Body ground
    B - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer off
    Below 1 V
    3C-34 (BZR) - Body ground
    B - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer on
    Pulse generation


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E98

  1. Disconnect the G77 certification ECU (smart key ECU assembly) connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G77-11 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    G77-2 (+B) - Body ground
    B - Body ground
    Auxiliary battery power supply
    Always
    11 to 14 V
    G77-10 (CUTB) - Body ground
    L - Body ground
    Dark current cut fuse pin input signal
    Always
    11 to 14 V

  3. Reconnect the G77 certification ECU (smart key ECU assembly) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G79-5 (IG) - G77-11 (E)
    V - W-B
    IG power supply
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    G78-19 (RSSI) - G77-11 (E)
    R - W-B*1
    P - W-B*2
    Communication channel switching circuit
    Procedure:
    1. Power switch off
    2. All doors closed
    3. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed
    11 to 14 V → Below 2 V
    G78-17 (RDAS) - G77-11 (E)
    LG - W-B
    Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
    Procedure:
    1. Power switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly not inside vehicle
    4. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
    5. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed
    Pulse generation
    (See waveform 1)
    G78-5 (RCO) - G77-11 (E)
    L - W-B
    Output to door control receiver (Power supply for door control receiver . Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
    3. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed
    Below 1 V → 4.5 to 5.5 V

    1. *1: for LHD
    2. *2: for RHD



  5. B251177E03
  6. Using an oscilloscope, check waveform 1.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 1(Reference) 
    Item
    Content
    Tester connection
    G78-17 (RDAS) - G77-11 (E)
    Tool setting
    5 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly not inside vehicle
    4. Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area
    5. Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed
    Text in Illustration 
    *a
    Before lock or unlock switch of electrical key transmitter sub-assembly pressed
    *b
    After lock or unlock switch of electrical key transmitter sub-assembly pressed


CHECK DOOR CONTROL RECEIVER ASSEMBLY

B280754E08

  1. Disconnect the M15 door control receiver connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M15-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the M15 door control receiver connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M15-2 (RSSI) - M15-1 (GND)
    Y - W-B
    Smart system receiving channel switching signal input
    All doors closed, all door lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed
    11 to 14 V → Below 2 V
    M15-5 (DATA) - M15-1 (GND)
    L - W-B
    Smart system recovery code output
    All doors closed, all door lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed
    Below 2 V → 11 to 14 V → Below 2 V
    M15-4 (+5) - M15-1 (GND)
    V - W-B
    Receive mode switching signal input
    Power switch off and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed
    Below 1 V → 4.5 to 5.5 V


CHECK DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

B280753E19

  1. Disconnect the M48 door control receiver connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connectors disconnected.


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M48-12 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the M48 door control receiver connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M48-6 (CSEL) - M48-12 (GND)
    Y - W-B
    Smart system receiving channel switching signal input
    The power switch off and close all doors
    No pulse generation → Pulse generation
    M48-9 (DATA) - M48-12 (GND)
    L - W-B
    Smart system recovery code output
    All doors closed, all doors lock and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed
    Below 1V → 10 to 16 V → Below 1V
    M48-10 (+5) - M48-12 (GND)
    V - W-B
    Receive mode switching signal input
    Power switch off and electrical key transmitter sub-assembly lock/unlock switch not pressed → electrical key transmitter sub-assembly lock/unlock switch pressed
    Below 1 V → 4.5 to 5.5 V