Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Interior Light Circuit

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:
  1. Personal Light
  2. Rear Dome Light (w/ Rear Dome Light)

HINT:
The DOME CUT relay supplies power to the lights not controlled by the illuminated entry system. If all the lights that use power from the DOME CUT relay do not turn on, check the DOME CUT relay circuit first (Click here).


WIRING DIAGRAM


E309640E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

  1. Check that the lights operate.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Illuminated Entry System
    Personal light and rear dome light*
    ON/OFF
    Interior light door switch DOOR

    1. *: w/ Rear Dome Light

    OK:
    Each light fades in.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT MAP LIGHT ASSEMBLY
  1. Remove the map light assembly (Click here).

  1. Inspect the map light assembly (Click here).

    OK:
    Map light assembly is normal.


Result 
Result
Proceed to
OK (w/ Rear Dome Light)
A
OK (w/o Rear Dome Light)
B
NG
C


B
Go to step 4

C
REPLACE MAP LIGHT ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - NO. 1 ROOM LIGHT ASSEMBLY)
  1. Disconnect the 3A and 3B instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q1-3 (B) - Q1-2 (CTY)
    No. 1 room light switch in DOOR position
    Below 1 Ω
    No. 1 room light switch in ON or OFF position
    10 kΩ or higher
    Q1-2 (CTY) - Body ground
    No. 1 room light switch in DOOR position
    10 kΩ or higher

  1. Connect the 3A and 3B instrument panel junction block assembly connector.



NG
REPLACE ROOF WIRE (INCLUDING NO. 1 ROOM LIGHT ASSEMBLY COMPONENTS THAT ARE PART OF THE WIRE HARNESS)
OK


4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAP LIGHT ASSEMBLY)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Q1-3 (B) - Body ground
    DOME CUT relay on
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3B instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q1-2 (CTY) - 3B-6
    Always
    Below 1 Ω
    Q1-2 (CTY) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



  1. Measure the resistance according to the value(s) in the table below.


    E173026E06


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3B-6 - MB-1 (ILE)
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)