Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (w/ Removable Headrest)

FRONT SEAT ASSEMBLY (w/ Removable Headrest) > REASSEMBLY

for Preparation Click here



1. INSTALL SEAT TRACK ADJUSTING HANDLE
  1. Engage the 2 springs to install the seat track adjusting handle to the separate type front seat cushion spring assembly.



2. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
  1. Engage the 4 guides to install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly.

  1. Install the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side)
  1. Type A:

    1. Engage the 3 claws to install the front seat cushion edge protector LH.

    2. Install the screw.

  1. Type B:

    1. Engage the 5 claws to install the front seat cushion edge protector LH.



4. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side)
  1. Type A:

    1. Engage the 3 claws to install the front seat cushion edge protector RH.

    2. Install the screw.

  1. Type B:

    1. Engage the 5 claws to install the front seat cushion edge protector RH.



5. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side)
  1. Type A:

    1. Engage the 3 claws to install the front seat cushion edge protector LH.

    2. Install the screw.

  1. Type B:

    1. Engage the 5 claws to install the front seat cushion edge protector LH.



6. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)
  1. Type A:

    1. Engage the 3 claws to install the front seat cushion edge protector RH.

    2. Install the screw.

  1. Type B:

    1. Engage the 5 claws to install the front seat cushion edge protector RH.



7. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)


    B301372
  1. Engage the clip to install the front seat lower cushion shield LH.

  1. Engage the hook as shown in the illustration.

  1. Install the screw.



8. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)


    B301374
  1. Engage the clip to install the front seat lower cushion shield RH.

  1. Engage the hook as shown in the illustration.

  1. Install the screw.



9. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B281074
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



10. INSTALL FRONT SEAT AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.



11. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
  1. Temporarily install the separate type front seatback cover with pad.

  1. Engage the 4 claws to install the 2 front seat headrest supports.

  1. Install the 3 brackets with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after installing the nut.
    3. Install the bracket securely.



    B301370
  1. Turn back the separate type front seatback cover.



  1. Type B:



      B386950
    1. Using hog ring pliers, install 2 new hog rings.

      NOTICE:
      1. Be careful not to damage the separate type front seatback cover.
      2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B301368
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B311802
  1. Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



12. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B301356
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B301354
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



13. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
  1. Temporarily install the separate type front seat cushion cover with pad.

  1. Engage each hook.



  1. for Front Passenger Side:



      B270301
    1. Engage the clamp to install the connector as shown in the illustration.



14. CONNECT FRONT SEAT AIRBAG ASSEMBLY
  1. for LH Side:

    1. Engage the claw and 6 clamps to install the front seat airbag assembly wire harness.

  1. for RH Side:

    1. Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.

  1. Engage the fastener to secure the front seat airbag assembly wire harness.



15. INSTALL FRONT SEAT LOWER CUSHION SHIELD (for Driver Side)
  1. Engage the 2 claws to install the front seat lower cushion shield.



16. INSTALL FRONT SEAT CUSHION SHIELD
  1. Engage the 2 claws, 4 guides and clip to install the front seat cushion shield.

  1. Install the screw.



17. INSTALL VERTICAL ADJUSTING HANDLE (for Driver Side)
  1. Install the vertical adjusting handle with the screw.



18. INSTALL RECLINING ADJUSTER RELEASE HANDLE
  1. Engage the claw to install the reclining adjuster release handle.



19. INSTALL SEAT ADJUSTER COVER CAP
  1. Install the 2 seat adjuster cover caps.



20. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)


    B309595E01
  1. Install the front seat inner belt assembly with the nut.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Engage the 2 clamps.

  1. Engage each clamp under the front seat assembly.



21. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)


    B309596E01
  1. Install the front seat inner belt assembly with the nut.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor parts of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

  1. Engage the clamp.

  1. Engage each clamp under the front seat assembly.



22. INSTALL FRONT SEAT INNER CUSHION SHIELD (for LHD Driver Side)
  1. Engage the 2 claws and 4 guides to install the front seat inner cushion shield.



23. INSTALL FRONT SEAT INNER CUSHION SHIELD (for RHD Driver Side)
  1. Engage the 2 claws and 5 guides to install the front seat inner cushion shield.



24. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)
  1. Engage the 2 claws and 5 guides to install the front seat inner cushion shield.



25. CONNECT SEPARATE TYPE FRONT SEATBACK COVER
  1. Connect the rubber band of the separate type front seatback cover.