Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (w/ Non-removable Headrest)

FRONT SEAT ASSEMBLY (w/ Non-removable Headrest) > REASSEMBLY

for Preparation Click here



1. INSTALL SEAT TRACK ADJUSTING HANDLE
  1. Engage the 2 springs to install the seat track adjusting handle to the separate type front seat cushion spring assembly.



2. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
  1. Engage the 4 guides to install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly.

  1. Install the 4 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
  1. Engage the 5 claws to install the front seat cushion edge protector LH.



4. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
  1. Engage the 5 claws to install the front seat cushion edge protector RH.



5. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    B296407
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 8 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



6. INSTALL FRONT SEAT AIRBAG ASSEMBLY

CAUTION:
  1. Do not reuse the nuts.
  2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

  1. Install the front seat airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps.



7. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
  1. Temporarily install the separate type front seatback cover with pad.

  1. Install the 3 brackets with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    CAUTION:
    1. For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
    2. Make sure that the strap is not twisted after installing the nut.
    3. Install the bracket securely.



    B296404
  1. Turn back the separate type front seatback cover.



    B396050
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B296402
  1. Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



    B311802
  1. Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



8. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B301356
  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



    B301354
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type front seat cushion cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



9. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


  1. for Front Passenger Side:



      B270301
    1. Engage the clamp to install the connector as shown in the illustration.

  1. Temporarily install the separate type front seat cushion cover with pad.

  1. Engage each hook.



10. CONNECT FRONT SEAT AIRBAG ASSEMBLY
  1. for Driver Side:

    1. Engage the claw and 6 clamps to install the front seat airbag assembly wire harness.

  1. for Front Passenger Side:

    1. Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.

  1. Engage the fastener to secure the front seat airbag assembly wire harness.



11. INSTALL FRONT SEAT CUSHION SHIELD
  1. Engage the 2 claws, 4 guides and clip to install the front seat cushion shield.

  1. Install the screw.



12. INSTALL RECLINING ADJUSTER RELEASE HANDLE
  1. Engage the claw to install the reclining adjuster release handle.



13. INSTALL SEAT ADJUSTER COVER CAP
  1. Install the 2 seat adjuster cover caps.



14. INSTALL FRONT SEAT BELT ANCHOR PLATE
  1. Install the front seat belt anchor plate.



15. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)


    B309595E01
  1. Install the front seat inner belt assembly with the nut.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Engage the 2 clamps.

  1. Engage each clamp under the front seat assembly.



16. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)


    B309596E01
  1. Install the front seat inner belt assembly with the nut.
    Text in Illustration 
    *1
    Protruding Part

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor parts of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

  1. Engage the clamp.

  1. Engage each clamp under the front seat assembly.



17. INSTALL FRONT SEAT INNER CUSHION SHIELD
  1. Engage the 2 claws and 5 guides to install the front seat inner cushion shield.



18. CONNECT SEPARATE TYPE FRONT SEATBACK COVER
  1. Connect the rubber band of the separate type front seatback cover.