Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT

FRONT WHEEL ALIGNMENT > ADJUSTMENT

for Preparation Click here


NOTICE:
If the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
  1. Perform zero point calibration of the yaw rate and acceleration sensor.



1. PRECAUTION


C253259E01
Standard values indicated by *1 and *2 in the specification tables are for the vehicles with a purple or blue identification mark on the bottom of the rear coil spring.
Text in Illustration 
*a
Colored identification mark on the bottom of the rear coil spring


2. INSPECT TIRES
  1. Check the tires for wear and proper inflation pressure.

    Cold Tire Inflation Pressure:

    Tire Size
    Front
    kPa (kgf/cm2, psi)
    Rear
    kPa (kgf/cm2, psi)
    175/65R15 84H
    230 (2.3, 33)
    220 (2.2, 32)
    195/50R16 84V
    220 (2.2, 32)
    200 (2.0, 29)
    185/60R15 84H
    220 (2.2, 32)
    220 (2.2, 32)



    C164558
  1. Using a dial indicator, check the runout of the tires.

    Maximum tire runout:
    Vertical:
    1.4 mm (0.0551 in.)
    Lateral:
    2.0 mm (0.0787 in.)



3. MEASURE VEHICLE HEIGHT

NOTICE:
  1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.
  4. Inspect while the vehicle is unloaded.
  5. The standard value shown here is a value that is used for adjusting the wheel alignment and does not indicate the height of an actual vehicle.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.



    C249970E01
  1. Measure the vehicle height.

    Measurement points:
    1. A: Ground clearance of front lower No. 1 suspension arm bushing set bolt center
    1. B: Ground clearance of rear axle beam bushing set bolt center
    1. C: Ground clearance of front wheel center
    1. D: Ground clearance of rear wheel center

    Vehicle Height (Unloaded Vehicle):

    Tire Size
    Front C - A
    Rear D - B
    175/65R15
    92 mm (3.62 in.)
    29 mm (1.14 in.)
    185/60R15
    93 mm (3.66 in.)
    79 mm (3.11 in.) *1
    69 mm (2.72 in.) *2
    32 mm (1.26 in.)
    14 mm (0.55 in.) *1
    4 mm (0.16 in.) *2
    195/50R16
    93 mm (3.66 in.)
    30 mm (1.18 in.)

    HINT:
    1. *1: Vehicles with purple identification mark on the bottom of the rear coil spring
    2. *2: Vehicles with blue identification mark on the bottom of the rear coil spring



4. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:
Inspect while the vehicle is unloaded.



    C132440E21
  1. Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.
    Text in Illustration 
    *1
    Turning Radius Gauge
    *2
    Camber-caster-kingpin Gauge

  1. Inspect the camber, caster and steering axis inclination.

    Camber (Unloaded Vehicle):

    Tire Size
    Camber Inclination
    Right-left Difference
    185/60R15
    -0°13' +/- 0°45' (-0.22° +/- 0.75°)
    -0°04' +/- 0°45' (-0.07° +/- 0.75°) *1
    0°05' +/- 0°45' (0.08° +/- 0.75°) *2
    0°30' (0.50°) or less
    175/65R15
    195/50R16
    -0°13' +/- 0°45' (-0.22° +/- 0.75°)

    HINT:
    1. *1: Vehicles with purple identification mark on the bottom of the rear coil spring
    2. *2: Vehicles with blue identification mark on the bottom of the rear coil spring


    Caster (Unloaded Vehicle):

    Tire Size
    Caster Inclination
    Right-left Difference
    175/65R15
    4°54' +/- 0°45' (4.90° +/- 0.75°)
    0°30' (0.50°) or less
    185/60R15
    4°59' +/- 0°45' (4.98° +/- 0.75°)
    4°41' +/- 0°45' (4.68° +/- 0.75°)*1
    4°32' +/- 0°45' (4.53° +/- 0.75°) *2
    195/50R16
    4°57' +/- 0°45' (4.95° +/- 0.75°)

    HINT:
    1. *1: Vehicles with purple identification mark on the bottom of the rear coil spring
    2. *2: Vehicles with blue identification mark on the bottom of the rear coil spring


    Steering Axis (Unloaded Vehicle):

    Tire Size
    Steering Axis Inclination Reference
    175/65R15
    11°23' (11.38°)
    185/60R15
    11°25' (11.42°)
    11°04' (11.07°) *1
    10°49' (10.82°) *2
    195/50R16
    11°25' (11.42°)

    HINT:
    1. *1: Vehicles with purple identification mark on the bottom of the rear coil spring
    2. *2: Vehicles with blue identification mark on the bottom of the rear coil spring



5. ADJUST CAMBER

NOTICE:
Inspect toe-in after the camber has been adjusted.

  1. Remove the front wheel.



    C249872
  1. Remove the 2 nuts on the lower side of the front shock absorber assembly.

    NOTICE:
    Keep the bolts inserted.

  1. Remove the top and bottom bolts one at a time and confirm that the steering knuckle can move freely in the front shock absorber assembly.

    HINT:
    1. Reinstall each bolt after removing it and confirming steering knuckle movement.
    2. If the steering knuckle does not move freely in the front shock absorber assembly, clean the installation surfaces of the front shock absorber assembly and the steering knuckle.

  1. Temporarily install the 2 nuts. (Step A)



    C131799
  1. Fully push or pull the front axle hub in the direction of the required adjustment. (Step B)

    Camber (Unloaded Vehicle):

    Tire Size
    Camber Inclination
    Right-left Difference
    185/60R15
    -0°13' +/- 0°45' (-0.22° +/- 0.75°)
    -0°04' +/- 0°45' (-0.07° +/- 0.75°) *1
    0°05' +/- 0°45' (0.08° +/- 0.75°) *2
    0°30' (0.50°) or less
    175/65R15
    195/50R16
    -0°13' +/- 0°45' (-0.22° +/- 0.75°)

    HINT:
    1. *1: Vehicles with purple identification mark on the bottom of the rear coil spring
    2. *2: Vehicles with blue identification mark on the bottom of the rear coil spring
    3. Perform adjustments so that the value is as close as possible to the median of the specified range.



    C249872
  1. Tighten the nuts.

    Torque:
    164 N*m{ 1672 kgf*cm , 121 ft.*lbf }

    NOTICE:
    Keep the bolts from rotating when tightening the nuts.

  1. Install the front wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



    C253266E01
  1. Check the camber.
    If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
    Camber adjustment amount = center of the specified range - measured value
    Check the combination of the installed bolts. Select appropriate bolts from the tables below to adjust the camber to the specified values.

    HINT:
    Try to adjust the camber to the center of the specified values.


    To move the axle hub toward (+) in step B
    To move the axle hub toward (-) in step B
    Refer to table (1) (To move the axle hub toward the positive side)
    Refer to table (2) (To move the axle hub toward the negative side)
    The vehicle body and suspension may be damaged if the camber cannot be correctly adjusted according to the table above.

    NOTICE:
    Replace the nut with a new one when replacing the bolt.




    1. Table (1) (To move the axle hub toward the positive side)


      C212217E01


      Text in Illustration 
      *A
      Table (1) (To move the axle hub toward the positive side)
      *B
      Selected Bolt Combination
      *a
      Installed Bolt
      *b
      Adjusting Value
      *c
      90109-15001
      *d
      90109-15002
      *e
      90109-15003
      *f
      90109-15004



    2. Table (2) (To move the axle hub toward the negative side)


      C212218E01


      Text in Illustration 
      *A
      Table (2) (To move the axle hub toward the negative side)
      *B
      Selected Bolt Combination
      *a
      Installed Bolt
      *b
      Adjusting Value
      *c
      90109-15001
      *d
      90109-15002
      *e
      90109-15003
      *f
      90109-15004

  1. If the camber was out of adjustment in the previous step, perform the adjust camber steps mentioned above. In step (A), replace the existing bolts with the selected bolts.

    HINT:
    Replace one bolt at a time when replacing both bolts.



6. INSPECT TOE-IN

NOTICE:
Inspect while the vehicle is unloaded.

  1. Bounce the vehicle up and down at the corners to stabilize the suspension.

  1. Release the parking brake and move the shift lever to N.

  1. Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)



    C188968E05
  1. Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
    Text in Illustration 
    *a
    Tread Center Mark
    *b
    Dimension B
    V100135
    Front of the Vehicle

  1. Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

    HINT:
    Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step C again.



    C188969E05
  1. Measure the distance between the tread center marks on the front of the wheels (dimension A).
    Text in Illustration 
    *a
    Dimension A
    V100135
    Front of the Vehicle

    Toe-in (Unloaded Vehicle):

    Tire Size
    Specified Condition
    175/65R15
    C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°)
    B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
    185/60R15
    C + D: 0°06' +/- 0°12' (0.09° +/- 0.19°)
    B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
    195/50R16
    C + D: 0°06' +/- 0°11' (0.09° +/- 0.19°)
    B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)

    HINT:
    Measure "B - A" only when "C + D" cannot be measured.

    If the toe-in is not within the specified range, adjust it at the rack ends.



7. ADJUST TOE-IN


    C249963E01
  1. Make sure that the thread length of the right and left rack ends are approximately the same.
    Text in Illustration 
    *a
    Thread Length

    Standard difference:
    1.5 mm (0.0591 in.) or less

  1. Remove the boot clips.



    C249964
  1. Loosen the tie rod end lock nuts.

  1. Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.

    1. Extend the shorter rack end if the measured toe-in deviates toward the outer-side.

    2. Shorten the longer rack end if the measured toe-in deviates toward the inner-side.

  1. Turn the right and left rack ends by an equal amount to adjust the toe-in.

    Toe-in (Unloaded Vehicle):

    Tire Size
    Specified Condition
    175/65R15
    C + D: 0°06' +/- 0°12' (0.10° +/- 0.21°)
    B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
    185/60R15
    C + D: 0°06' +/- 0°12' (0.09° +/- 0.19°)
    B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)
    195/50R16
    C + D: 0°06' +/- 0°11' (0.09° +/- 0.19°)
    B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)

    HINT:
    Perform adjustments so that the value is as close as possible to the median of the specified range.

  1. Make sure that the thread lengths of the right and left rack ends are the same.

  1. Tighten the tie rod end lock nuts.

    Torque:
    75 N*m{ 760 kgf*cm , 55 ft.*lbf }

  1. Place the boots on the seats and install the clips.

    HINT:
    Make sure that the boots are not twisted.



8. INSPECT WHEEL ANGLE


    C132439E11
  1. Put tread center marks on the rearmost points of a turning radius gauge.
    Text in Illustration 
    *a
    Inside
    *b
    Outside
    V100135
    Front of the Vehicle

  1. Turn the steering wheel fully to the left and right and measure the turning angle.

    NOTICE:
    Inspect while the vehicle is unloaded.


    Wheel Angle (Unloaded Vehicle):

    Tire Size
    -
    Inside Wheel
    Outside Wheel Reference
    175/65R15 (5J)
    -
    40°50' +/- 2° (40.83° +/- 2°)
    35°11' (35.18°)
    175/65R15 (5.5J)
    -
    40°04' +/- 2° (40.07° +/- 2°)
    34°41' (34.68°)
    185/60R15
    for LHD
    40°50' +/- 2° (40.83° +/- 2°)
    41°09' +/- 2° (41.15° +/- 2°) *1
    41°21' +/- 2° (41.35° +/- 2°) *2
    35°09' (35.15°)
    35°30' (35.50°) *1
    35°44' (35.73°) *2
    for RHD
    40°00' +/- 2° (40.00° +/- 2°)
    40°21' +/- 2° (40.35° +/- 2°) *1
    40°32' +/- 2° (40.53° +/- 2°) *2
    34°38' (34.63°)
    35°06' (35.10°) *1
    35°14' (35.23°) *2
    195/50R16
    -
    32°37' +/- 2° (32.62° +/- 2°)
    29°35' (29.58°)

    HINT:
    1. *1: Vehicles with purple identification mark on the bottom of the rear coil spring
    2. *2: Vehicles with blue identification mark on the bottom of the rear coil spring

    1. If the right and left inside wheel angles differ from the specified value, check and adjust the right and left rack end lengths.



9. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


10. PERFORM YAW RATE AND ACCELERATION SENSOR CALIBRATION
(Click here)