Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Only Back Door cannot be Opened

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) receives signals from the back door opener switch assembly. Then, the main body ECU (multiplex network body ECU) activates the back door lock motor.

WIRING DIAGRAM


B308524E04


INSPECTION PROCEDURE

NOTICE:
  1. The power door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.

1.CHECK POWER DOOR LOCK OPERATION (BASIC FUNCTION)
  1. Check the power door lock basic function (Click here).

    OK:
    The power door lock basic functions operate normally.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK STATUS)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.


Main Body (Main Body ECU (Multiplex Network Body ECU)) 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Back Door Open
Back door lock/Permit or Prohibt
Permit: Back door unlocked
Prohibt: Back door locked
-

OK:
The intelligent tester indicates Permit or Prohibit according to the door lock operation shown in the table.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Trunk and Back-Door Open
    Operate back door lock motor
    ON or OFF
    -

    OK:
    The back door lock assembly unlatches when ON is selected.



NG
Go to step 4
OK

GO TO SMART ENTRY AND START SYSTEM 

4.INSPECT BACK DOOR LOCK ASSEMBLY


    E222051E03
  1. Remove the back door lock assembly (Click here).

  1. Check the operation of the door lock motor.

    1. Move the door lock to the lock position.

    2. Apply auxiliary battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Connection
      Result
      Auxiliary battery positive (+) → Terminal 1 (ACT+)
      Auxiliary battery negative (-) → Terminal 2 (ACT-)
      Unlocks

  1. Check the operation of the door courtesy switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (ACT-) - 3 (D+)
      Locked
      10 kΩ or higher
      2 (ACT-) - 3 (D+)
      Unlocked
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Back Door Lock Assembly)
      *b
      Lock
      *c
      Unlock



NG
REPLACE BACK DOOR LOCK ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the 3D instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T5-1 (ACT+) - 3D-9 (TR+)
    Always
    Below 1 Ω
    T5-1 (ACT+) - Body ground
    Always
    10 kΩ or higher
    T5-3 (D+) - 3D-35 (BCTY)
    Always
    Below 1 Ω
    T5-3 (D+) - Body ground
    Always
    10 kΩ or higher
    T5-2 (ACT-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Replace the instrument panel junction block assembly (Click here).


NEXT


7.CHECK BACK DOOR OPEN OPERATION
  1. Check that the back door can be opened.

    OK:
    The back door can be opened normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)