Home › Drivetrain › P510 HYBRID TRANSMISSION / TRANSAXLE › SHIFT LEVER

SHIFT LEVER > INSTALLATION

for Preparation Click here



1. INSTALL SHIFT LEVER ASSEMBLY
  1. Engage the 2 clamps and connect the instrument panel wire to the shift lever assembly.

  1. Connect the 2 connectors to the shift lever assembly.

  1. Temporarily install the shift lever assembly with the 4 bolts.



    C251061E01
  1. Fully tighten the 4 bolts in the order shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C195134E04
  1. Rotate the nut of the transmission control cable approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.
    Text in Illustration 
    *1
    Nut
    *2
    Lock
    *a
    Rotate Approximately 180°
    *b
    Push In



    C250999E01
  1. Install the transmission control cable assembly to the shift lever plate.
    Text in Illustration 
    *1
    Shift Lever Plate
    *2
    Lock
    *a
    Install
    *b
    Projecting Part

    NOTICE:
    1. Install the cable outer with the projecting part facing upwards.
    2. After installation, make sure that the cable outer lock is projecting from A as shown in the illustration.
    3. Check that the transmission control cable assembly is securely locked.



    C249909
  1. Confirm that the shift lever is in N, and then install the cable end to the shift lever assembly.

    NOTICE:
    1. Securely install the cable end to the shift lever assembly.
    2. Install the cable end so that its adjustment lock section is on the driver side.



3. INSTALL REAR CONSOLE BOX ASSEMBLY
(Click here)


4. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    C261403
  1. Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.



5. INSPECT SHIFT LEVER POSITION
  1. While moving the shift lever from N to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

  1. Turn the power switch on (READY) and check the following:

    1. When the shift lever is moved to D, the vehicle moves forward.

    2. When the shift lever is moved to R, the vehicle moves in reverse.

      NOTICE:
      The vehicle should not move when the shift position indicator is off.



6. ADJUST SHIFT LEVER POSITION
  1. Apply the parking brake and move the shift lever to N.

  1. Remove the rear console box assembly (Click here).



    C258106E01
  1. Slide the adjuster case cover in the direction shown by the arrow.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Adjuster Case Cover



    C258107E01
  1. Using a precision screwdriver, pull out the lock piece of the adjuster case.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Lock Piece

  1. Using your fingers, gently pull the cable rod towards the rear of the vehicle to remove backlash.



    C258108E01
  1. Push in the lock piece of the adjuster case to lock it.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Lock Piece
    *3
    Cable Rod



    C258109E01
  1. Move the adjuster case cover in the direction shown by the arrow.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Lock Piece
    *3
    Adjuster Case Cover

    NOTICE:
    If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the cable will not be able to lock, and reliable shift operation will not be possible.

  1. Install the rear console box assembly (Click here).