Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. PRECAUTION


    A267872E01
  1. When removing and installing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.
    Text in Illustration 
    *1
    Cord

    NOTICE:
    Depending on the arrangement of the inlet hose during removal, the inlet hose and rear suspension may interfere and cause fuel leaks.



2. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(Click here)


3. DRAIN FUEL


4. REMOVE FUEL TANK CAP ASSEMBLY


5. REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR


    A267873
  1. Remove the 2 nuts and front No. 4 floor heat insulator.



6. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    A267874
  1. Pinch and remove the clip as shown in the illustration.

  1. Remove the bolt and No. 1 fuel tank protector sub-assembly.



7. DISCONNECT NO. 2 FUEL EMISSION TUBE


    A267876
  1. Loosen the clip and disconnect the No. 2 fuel emission tube.



8. REMOVE NO. 1 FUEL TUBE PROTECTOR


    A268480E01
  1. Remove the No. 1 fuel tube protector from the fuel tube connector.
    Text in Illustration 
    *1
    No. 1 Fuel Tube Protector



9. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A267875E01
  1. Pull the tabs of the retainer to disengage the lock claws and pull out the fuel tank main tube sub-assembly.
    Text in Illustration 
    *1
    Fuel Tank Main Tube Sub-assembly
    *2
    Fuel Tank Pipe Setting Holder
    *3
    Retainer
    *4
    Nylon Tube
    *5
    O-ring
    *6
    Fuel Tube Connector
    *7
    Fuel Pipe

    NOTICE:
    1. Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and fuel pipe before performing this work.
    2. Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.
    3. Only disconnect the fuel tube connector by hand.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube connector.
    6. If the fuel tube connector and fuel pipe are stuck, push and pull to release them.

  1. Disengage the 3 clamps and separate the fuel tank pipe setting holder.



10. REMOVE FUEL TANK ASSEMBLY


    A267877E01
  1. Disengage the 2 clamps and separate the air tube.
    Text in Illustration 
    *1
    Fuel Tank Filler Pipe Flange Plate
    *2
    Air Tube

  1. Remove the bolt.

  1. Disengage the claw and remove the fuel tank filler pipe flange plate.



    A267879
  1. Support the fuel tank assembly using an engine lifter.



    A267878
  1. Separate the 2 fuel hoses shown in the illustration.



    A267880
  1. Remove the 4 bolts and fuel tank assembly.

    NOTICE:
    1. Slowly operate the engine lifter to lower the fuel tank.
    2. Do not drop the fuel tank.



11. REMOVE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY


    A267881
  1. Disengage the clamp and remove the No. 1 canister outlet hose sub-assembly.



12. REMOVE FUEL HOSE CLAMP


    A267882
  1. Remove the fuel hose clamp.



13. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A267883
  1. Disengage the 2 clamps and remove the fuel tank main tube sub-assembly.



14. REMOVE NO. 2 FUEL EMISSION TUBE


    A267884
  1. Disengage the 2 clamps and remove the No. 2 fuel emission tube.



15. REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT


    A267885
  1. Disengage the clamp and remove the No. 2 fuel tank filler pipe support.



16. REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT


    A267886
  1. Disengage the clamp and remove the No. 1 fuel tank filler pipe support.