Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A9C-123    Hybrid Battery Temperature Sensor "A" Range / Performance

DTC    P0AC6-123    Hybrid Battery Temperature Sensor "B" Range / Performance

DTC    P0ACB-123    Hybrid Battery Temperature Sensor "C" Range / Performance

DTC    P3065-123    Hybrid Battery Temperature Sensor Range/Performance Stuck "A"

for Preparation Click here


DESCRIPTION


  1. The battery temperature sensors are provided at 3 locations of the HV battery. The resistance of the thermistor, which is built into each battery temperature sensor, varies in accordance with changes in the HV battery temperature. The lower the battery temperature, the higher the thermistor resistance. Conversely, the higher the temperature, the lower the resistance. The battery smart unit uses the battery temperature sensors to detect the HV battery temperature, and sends the detected value to the hybrid vehicle control ECU. Based on the results of this detection, the hybrid vehicle control ECU controls the blower fan. (The blower fan starts when HV battery temperature rises above a predetermined level.)

    Temperature Sensor Identification Cross Reference Table:
    DTC Title Sensor
    Battery Temperature Sensor
    Intelligent tester Display
    A
    0
    1
    B
    1
    2
    C
    2
    3

    HINT:
    For example, sensor A in the DTC title is battery temperature sensor (No. 0). This sensor is displayed as Temp of Batt TB1 in the Data List.



    A171806E02


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A9C
P0AC6
P0ACB
P3065
123
When the battery temperature sensor performance is abnormal (1 trip detection/2 trip detection)
  1. HV battery
  2. Battery smart unit
  3. Wire harness or connector

WIRING DIAGRAM


A244328E08


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

  3. When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



B
GO TO DTC CHART (P0AFC-123) (Click here)
A


2.CHECK INSTALLATION OF BATTERY TEMPERATURE SENSOR

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the upper hybrid battery cover sub-assembly .



  1. Visually check the installation condition of the relevant battery temperature sensor.


    A266554E01

    Standard Condition:
    Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely.

    Result:
    Result
    Proceed to
    Each battery temperature sensor is installed in the correct location with the correct orientation and its claws are engaged securely.
    A
    Claws are damaged.
    B
    Any of battery temperature sensors are not installed correctly, but claws are not damaged.
    C

    NOTICE:
    Do not use a stick or similar object to push on the sensors when inspecting them. Doing so may result in damage to the sensors.


    Text in Illustration 
    *1
    Battery Temperature Sensor 0
    *2
    Battery Temperature Sensor 1
    *3
    Battery Temperature Sensor 2
    -
    -

  1. Install the upper hybrid battery cover sub-assembly.



B
REPLACE HV BATTERY (Click here)

C
INSTALL PARTS CORRECTLY
A


3.CHECK HV BATTERY (BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid battery shield sub-assembly .

  1. Disconnect connectors d1 and M39 from the battery smart unit.



    A260171E02
  1. Measure the resistance of the circuit for the malfunctioning sensor (battery temperature sensor 0 to 2).
    Tester Connection 
    Tester Connection
    Battery Temperature Sensor No.
    d1-4 (TBO) - d1-10 (GBO)
    0
    d1-3 (TB1) - d1-9 (GB1)
    1
    d1-2 (TB2) - d1-8 (GB2)
    2

    Standard Resistance:
    Thermistor Temperature
    Switch Condition
    Specified Condition
    0°C (32°F)
    Power switch off
    26.7 to 27.8 kΩ
    25°C (77°F)
    Power switch off
    9.9 to 10.1 kΩ
    40°C (104°F)
    Power switch off
    5.73 to 5.92 kΩ

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Battery Smart Unit)



    A244309E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Standard Resistance
    d1-4 (TBO) - M39-3 (IGCT)
    Power switch off
    10 kΩ or more
    d1-4 (TBO) - M39-6 (GND)
    Power switch off
    10 kΩ or more
    d1-10 (GBO) - M39-3 (IGCT)
    Power switch off
    10 kΩ or more
    d1-10 (GBO) - M39-6 (GND)
    Power switch off
    10 kΩ or more
    d1-3 (TB1) - M39-3 (IGCT)
    Power switch off
    10 kΩ or more
    d1-3 (TB1) - M39-6 (GND)
    Power switch off
    10 kΩ or more
    d1-9 (GB1) - M39-3 (IGCT)
    Power switch off
    10 kΩ or more
    d1-9 (GB1) - M39-6 (GND)
    Power switch off
    10 kΩ or more
    d1-2 (TB2) - M39-3 (IGCT)
    Power switch off
    10 kΩ or more
    d1-2 (TB2) - M39-6 (GND)
    Power switch off
    10 kΩ or more
    d1-8 (GB2) - M39-3 (IGCT)
    Power switch off
    10 kΩ or more
    d1-8 (GB2) - M39-6 (GND)
    Power switch off
    10 kΩ or more
    d1-1 (TCO) - M39-3 (IGCT)
    Power switch off
    10 kΩ or more
    d1-1 (TCO) - M39-6 (GND)
    Power switch off
    10 kΩ or more
    d1-7 (GCO) - M39-3 (IGCT)
    Power switch off
    10 kΩ or more
    d1-7 (GCO) - M39-6 (GND)
    Power switch off
    10 kΩ or more

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Battery Smart Unit)

  1. Connect the battery smart unit connectors.

  1. Install the No. 1 hybrid battery shield sub-assembly.



NG
Go to step 4
OK

REPLACE BATTERY SMART UNIT (Click here)  

4.CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR)

CAUTION:
Be sure to wear insulated gloves and protective goggles.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the upper hybrid battery cover sub-assembly .

  1. Check the wire harness and connectors of the battery temperature sensor for abnormalities by sight and touch.

    Specified Condition:
    There are no open or short circuits in the wire harness and connectors. There are no short circuits to other wire harnesses.

HINT:
Because the battery harness is not available as a supply part, if the harness cannot be repaired, replace the HV battery assembly.

  1. Install the upper hybrid battery cover sub-assembly.



NG
REPAIR HARNESS OR CONNECTOR (BATTERY TEMPERATURE SENSOR)
OK

REPLACE HV BATTERY (Click here)