Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P3011-123    Battery Block 1 Becomes Weak

DTC    P3012-123    Battery Block 2 Becomes Weak

DTC    P3013-123    Battery Block 3 Becomes Weak

DTC    P3014-123    Battery Block 4 Becomes Weak

DTC    P3015-123    Battery Block 5 Becomes Weak

DTC    P3016-123    Battery Block 6 Becomes Weak

DTC    P3017-123    Battery Block 7 Becomes Weak

DTC    P3018-123    Battery Block 8 Becomes Weak

DTC    P3019-123    Battery Block 9 Becomes Weak

DTC    P3020-123    Battery Block 10 Becomes Weak

for Preparation Click here


DESCRIPTION

  1. Refer to the Description for DTC P0A80-123 .

DTC No.
INF Code
DTC Detection Condition
Trouble Area
P3011
P3012
P3013
P3014
123
Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
  1. HV battery
  2. Battery smart unit
P3015
123
Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
  1. HV battery
  2. Battery smart unit
  3. Service plug grip
P3016
P3017
P3018
P3019
P3020
123
Presence of a malfunctioning block is determined based on each battery block voltage (1 trip detection).
  1. HV battery
  2. Battery smart unit

HINT:
  1. P3011-123 to P3019-123 and P3020-123 will not be set unless the vehicle is driven for approximately 10 minutes after clearing the DTCs.
  2. In order to ensure HV battery performance, appropriate cooling performance must be maintained. Perform the following as necessary:
    1. Make sure the air intake port is not blocked.
    2. Clean the battery cooling blower filter.


INSPECTION PROCEDURE

CAUTION:
When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

1.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



B
GO TO DTC CHART (P0AFC-123) (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (VB1 - VB10)
  1. Ensure the safety of the areas in front and at the back of the vehicle.

  1. Apply the parking brake and secure the wheels using chocks.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (READY).

  1. Fully warm up the engine and turn the air conditioning off.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery block Vol -V01 to V10.

  1. Firmly depress the brake pedal with your left foot.

  1. Move the select lever to D.

  1. Record each battery block voltage from the data list "Battery block Vol -V01 to V10" while fully depressing the accelerator pedal.

  1. Compare the battery block voltages "Battery block Vol -V01 to V10" between the even and odd number groups in each combination shown in the table below.


Table 1 
Circuit A Battery Block
Circuit B Battery Block
Condition
Battery Block Vol -V01 (VB1)
Battery Block Vol -V02 (VB2)
"Battery Block Vol -V01" - "Battery Block Vol -V02" = 0.3 V or more
Battery Block Vol -V04 (VB4)
Battery Block Vol -V03 (VB3)
"Battery Block Vol -V04" - "Battery Block Vol -V03" = 0.3 V or more
Battery Block Vol -V05 (VB5)
Battery Block Vol -V06 (VB6)
"Battery Block Vol -V05" - "Battery Block Vol -V06" = 0.3 V or more
Battery Block Vol -V08 (VB8)
Battery Block Vol -V07 (VB7)
"Battery Block Vol -V08" - "Battery Block Vol -V07" = 0.3 V or more
Battery Block Vol -V09 (VB9)
Battery Block Vol -V10 (VB10)
"Battery Block Vol -V09" - "Battery Block Vol -V10" = 0.3 V or more

Table 2 
Circuit A Battery Block
Circuit B Battery Block
Condition
Battery Block Vol -V01 (VB1)
Battery Block Vol -V02 (VB2)
"Battery Block Vol -V02" - "Battery Block Vol -V01" = 0.3 V or more
Battery Block Vol -V04 (VB4)
Battery Block Vol -V03 (VB3)
"Battery Block Vol -V03" - "Battery Block Vol -V04" = 0.3 V or more
Battery Block Vol -V05 (VB5)
Battery Block Vol -V06 (VB6)
"Battery Block Vol -V06" - "Battery Block Vol -V05" = 0.3 V or more
Battery Block Vol -V08 (VB8)
Battery Block Vol -V07 (VB7)
"Battery Block Vol -V07" - "Battery Block Vol -V08" = 0.3 V or more
Battery Block Vol -V09 (VB9)
Battery Block Vol -V10 (VB10)
"Battery Block Vol -V10" - "Battery Block Vol -V09" = 0.3 V or more

A298791E01

HINT:
When an internal malfunction occurs in the battery smart unit, this symptom (difference in voltage of 0.3 V or more for all 5 pairs of blocks) will occur.

Result:
Result
Proceed to
All conditions in table 1 are met.
A
All conditions in table 2 are met.
Other than above.
B

  1. Turn the power switch off.



B
Go to step 3
A

REPLACE BATTERY SMART UNIT (Click here)  

3.CHECK DTC OUTPUT (HYBRID CONTROL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Check if DTCs are output.
    Result 
    Result
    Proceed to
    P3015-123 is output.
    A
    P3015-123 is not output.
    B

    HINT:
    DTC P3015-123 may also stored if there is foreign matter, etc. adhering to the connecting part of the service grip.

  1. Turn the power switch off.



B
REPLACE HV BATTERY (Click here)
A

REPLACE SERVICE PLUG GRIP AND HV BATTERY (Click here)