Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM

VEHICLE PROXIMITY NOTIFICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK VEHICLE APPROACHING SPEAKER CONTROLLER

E228856E25

  1. Disconnect the G85 vehicle approaching speaker controller connector.

  2. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G85-1 (IG) - Body ground
    LG - Body ground
    IG power supply
    Power switch on (IG)
    11 to 14 V
    Power switch off
    Below 1 V
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Measure the resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G85-7 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  4. Reconnect the G85 vehicle approaching speaker controller connector.



  5. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G85-2 (STP) - G85-7 (GND)
    P - W-B
    Stop light signal input
    Power switch off, brake pedal depressed
    8 V or higher
    Power switch off, brake pedal released
    Below 1 V
    G85-3 (SP+) - G85-8 (SP-)
    R - G
    Vehicle approaching speaker output
    Vehicle approaching speaker operating
    A waveform synchronized with the sound is output.
    (See Waveform 1)
    G85-5 (SW) - G85-7 (GND)
    P - W-B
    Vehicle approaching speaker switch signal
    Power switch on (IG), vehicle approaching speaker switch being pushed and held
    6 V or higher
    Power switch on (IG), vehicle approaching speaker switch not pushed
    Below 1 V
    G85-6 (SPD) - G85-7 (GND)
    L - W-B
    Speed signal input
    Power switch on (IG), wheel being rotated
    Pulse generation
    (See Waveform 2)
    G85-9 (PRST) - G85-7 (GND)
    B - W-B
    SIL communication system
    Power switch on (IG), during transmission
    Pulse generation
    (See Waveform 3)
    G85-10 (IND) - G85-7 (GND)
    L - W-B
    Vehicle proximity notification off indicator light signal
    Power switch on (IG), vehicle proximity notification off indicator light off
    11 to 14 V
    Power switch on (IG), vehicle proximity notification off indicator light on
    Below 1.8 V
    G85-11 (SFTP) - G85-7 (GND)
    G - W-B
    Transmission shift main switch signal input
    Power switch on (IG), shift lever in P
    8 V or higher
    Power switch on (IG), shift lever not in P
    Below 2.5 V
    G85-12 (OPSW) - G85-7 (GND)
    GR - W-B
    Engine oil pressure switch signal input
    Idling*
    8 V or higher
    Power switch on (IG)
    Below 2 V
    *: Put the engine in inspection mode (Click here).
    If the result is not as specified, there is a problem in the vehicle approaching speaker controller or wire harness.



      E289167
    1. Waveform 1
      Item
      Condition
      Tool setting
      1 V/DIV., 200 ms./DIV.
      Vehicle condition
      Vehicle approaching speaker operating



    2. E267248E02
    3. Waveform 2
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Power switch on (IG), wheel being rotated

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



    4. E288729E01
    5. Waveform 3
      Item
      Condition
      Tool setting
      5 V/DIV., 10 ms./DIV.
      Vehicle condition
      Power switch on (IG), during transmission