Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY

HV RELAY ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. REMOVE SERVICE PLUG GRIP
(Click here)


3. REMOVE REAR SEAT CUSHION ASSEMBLY


    B297552E01
  1. Disengage the 2 clips.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side



    B296114E01
  1. Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Follow the instructions below carefully as the cushion frame can be deformed easily.


    1. Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

    2. Repeat the step above for the other hook.

  1. Remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



4. REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY


    A266710
  1. Remove the 4 bolts and rear seat cushion leg sub-assembly.



5. REMOVE INVERTER TERMINAL COVER


    A266706E01
  1. Remove the 2 bolts and inverter terminal cover.
    Text in Illustration 
    *1
    Interlock Connector

    CAUTION:
    An interlock connector is installed to the inverter terminal cover. Make sure to remove the inverter terminal cover before removing the inverter cover.

    NOTICE:
    Make sure to pull the inverter cover straight up, as a connector is connected to the bottom of the cover.



6. REMOVE INVERTER COVER

CAUTION:
Wear insulated gloves.



    A266688
  1. Remove the 7 bolts and inverter cover.

    CAUTION:
    An interlock connector is installed to the inverter terminal cover. Make sure to remove the inverter terminal cover before removing the inverter cover.



7. CHECK TERMINAL VOLTAGE

CAUTION:
Wear insulated gloves.

NOTICE:
Do not allow any foreign matter or water to enter the inverter with converter assembly.



    A267098
  1. Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.

    Standard voltage:
    0 V

    HINT:
    Use measuring range of DC 750 V or more on the voltmeter.



8. INSTALL INVERTER COVER

CAUTION:
Wear insulated gloves.



    A266688E01
  1. Temporarily install the inverter cover with the 7 bolts to the inverter with converter assembly.

    CAUTION:
    An interlock connector is installed to the inverter terminal cover. Make sure to install the inverter terminal cover after installing the inverter cover.

    NOTICE:
    Visually confirm that the inverter cover waterproofing rubber is securely installed before installing the inverter cover.

  1. Fully tighten the bolt (A).

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Fully tighten the bolt (B).

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Fully tighten the 5 bolts (C).

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



9. INSTALL INVERTER TERMINAL COVER

CAUTION:
Wear insulated gloves.



    A266706E01
  1. Temporarily install the inverter terminal cover with the 2 bolts to the inverter with converter assembly.
    Text in Illustration 
    *1
    Interlock Connector

    CAUTION:
    An interlock connector is installed to the inverter terminal cover. Make sure to install the inverter terminal cover after installing the inverter cover.

    NOTICE:
    1. Visually confirm that the inverter terminal cover waterproofing rubber is securely installed before installing the inverter terminal cover.
    2. Make sure that the interlock connector is fully engaged.

  1. Fully tighten the bolt (A).

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Fully tighten the bolt (B).

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



10. REMOVE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY


    B295147
  1. Disengage the 2 clamps.

  1. Disconnect the connector and remove the No. 3 indoor electrical key antenna assembly.

    NOTICE:
    Be careful when removing the indoor electrical key antenna assembly. If the antenna is dropped, replace it with a new one.



11. REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT


    A266728
  1. Remove the clip and No. 1 hybrid battery exhaust duct.



12. REMOVE NO. 1 HYBRID VEHICLE BATTERY COVER PANEL LH

CAUTION:
Wear insulated gloves.



    A266761E01
  1. Using the service plug grip, remove the battery cover lock striker.
    Text in Illustration 
    *1
    Service Plug Grip
    *2
    Battery Cover Lock Striker
    *3
    Button
    *a
    Projection
    *b
    Turn

    HINT:
    Insert the projection part of the service plug grip, and turn the button of the battery cover lock striker counterclockwise, and release the lock.

  1. Remove the 4 nuts and No. 1 hybrid vehicle battery cover panel LH.



13. DISCONNECT FRAME WIRE

CAUTION:
Wear insulated gloves.

NOTICE:
Insulate the disconnected connectors with insulating tape.



    A266764E01
  1. Disconnect the 2 connectors shown in the illustration.
    Text in Illustration 
    *1
    Shielded Wire Ground

  1. Disconnect the shielded wire ground and frame wire.



14. REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

CAUTION:
Wear insulated gloves.



    A266763
  1. Disconnect the connector.



    A266759
  1. Disconnect the connector and clamp.



    A266758
  1. Disconnect the 2 connectors and 3 clamps.



    A266766
  1. Remove the 2 bolts and 2 nuts.



    A267092E01
  1. Move the HV battery toward the front of the vehicle.
    Text in Illustration 
    *a
    Front of Vehicle

    HINT:
    Move the HV battery to a position where both the No. 2 hybrid battery shield sub-assembly and the hybrid battery junction block assembly can be removed.



    A266775
  1. Remove the 2 bolts, nut and No. 2 hybrid battery shield sub-assembly.



15. REMOVE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:
Wear insulated gloves.

NOTICE:
Insulate the disconnected terminals with insulating tape.



    A266777
  1. Open the terminal cover.



    A266779
  1. Using an insulated tool, remove the 2 bolts.



    A266776
  1. Disconnect the connector.



    A255175
  1. Remove the 3 bolts and hybrid battery junction block assembly.